ДСТУ EN ISO 16089:2016 Станки. Требования к безопасности. Стационарные шлифовальные станки (EN ISO 16089:2015, IDT; ISO 16089:2015, IDT)

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)

Наказ від 20.07.2016 № 209

EN ISO 16089:2015

Machine tools - Safety - Stationary grinding machines
(ISO 16089:2015)

прийнято як національний стандарт
методом «підтвердження» за позначенням

ДСТУ EN ISO 16089:2016
(EN ISO 16089:2015, IDT; ISO 16089:2015, IDT)

Станки. Вимоги щодо безпеки. Стаціонарні шліфувальні верстати

З наданням чинності від 2016–07–22

Відповідає офіційному тексту

З питань придбання офіційного видання звертайтесь
до національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.org.ua)

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

3.1 General terms

3.2 Parts of grinding machines

3.3 Modes of safe operation (MSO)

3.4 Types and groups of grinding machines defined in this International Standard

3.5 Speeds and axes speed

4 List of significant hazards

4.1 General

4.2 Main hazard zones

4.3 Significant hazards and hazardous situations covered by this International Standard

5 Safety requirements and/or measures

5.1 General requirements

5.2 Specific requirements resulting from mechanical hazards identified in Table 2, Nos. 1.1 - 1.4, 1.6 and 1.7

5.3 Specific requirements resulting from electrical hazards

5.4 Specific requirements resulting from noise hazards

5.5 Specific requirements resulting from vibration hazards

5.6 Specific requirements resulting from radiation hazards

5.7 Specific requirements resulting from materials or substance hazards

5.8 Specific requirements resulting from neglect of ergonomic principles hazards

5.9 Specific requirements resulting from unexpected start-up, over-run, or over- speed hazards

5.10 Specific requirements resulting from variation in the rotational speed hazards

5.11 Specific requirements resulting from failure of the power supply hazards

5.12 Specific requirements resulting from failure of the control circuit hazards

5.13 Specific requirements resulting from ejected fluids or objects hazards

5.14 Specific requirements resulting from loss of stability hazards

5.15 Specific requirements resulting from slips, trips and fall of persons hazards

6 Verification of the safety requirements and/or protective measures

7 Information for use

7.1 Marking

7.2 Instruction for use

Annex A (normative) Abrasive product guards, work zone enclosures, and their combinations

Annex B (informative) Impact test for guards — Bursting test

Annex C (informative) Impact test for guards — Projectile impact

Annex D (normative) Clamping methods for abrasive products and safety requirements for tool holding devices

Annex E (informative) Noise reduction

Annex F (informative) Noise emission determination

Annex G (normative) Requirements for grinding machines for the machining of materials generating flammable and explosive dusts

Annex H (informative) Measures for the use of flammable metalworking fluids

Annex I (informative) Examples for the integration of extraction and fire extinguishing systems when using flammable metalworking fluids

Annex J (informative) Functional safety — Example for rotational speed limit monitoring of the wheel spindle

Annex K (informative) MSO 3 (Optional special mode for manual intervention under restricted operating conditions) – Examples

Bibliography

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online