ДСТУ EN 61442:2016 Методы испытаний арматуры силовых кабелей на номинальное напряжение от 6 кВ (Um = 7,2 кВ) до 36 кВ (Um = 42 кВ) (EN 61442:2005, IDT)

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)

Наказ від 07.09.2016 № 266

EN 61442:2005

Test methods for accessories for power cables with rated voltages from 6 kV (Um = 7,2 kV) up to 36 kV (Um = 42 kV)

прийнято як національний стандарт
методом «підтвердження» за позначенням

ДСТУ EN 61442:2016
 (EN 61442:2005, IDT)

Методи випробування арматури силових кабелів на номінальну напругу від 6 кВ (Um = 7,2 кВ) до 36 кВ (Um = 42 кВ)

З наданням чинності від 2016–09–15

CONTENTS

FOREWORD

1 Scope

2 Normative references

3 Test installations and conditions

4 AC voltage tests

4.1 Dry test for all accessories

4.2 Wet test for outdoor terminations

4.3 Test in water for stop ends

5 DC voltage tests

5.1 Installation

5.2 Method

6 Impulse voltage tests

6.1 Installation

6.2 Method

6.3 Test at elevated temperature

7 Partial discharge test

7.1 Method

7.2 Test at elevated temperature

8 Tests at elevated temperature

8.1 Installation and connection

8.2 Measurement of temperature

9 Heating cycles voltage test

9.1 Installation

9.2 Test in air

9.3 Test in water

9.4 Immersion test for outdoor terminations

10 Thermal short-circuit test (screen)

10.1 Installation

10.2 Method

11 Thermal short-circuit test (conductor)

11.1 Installation

11.2 Method

12 Dynamic short-circuit test

12.1 Installation

12.2 Method

13 Humidity and salt fog tests

13.1 Apparatus

13.2 Installation

13.3 Method

14 Impact test at ambient temperature

15 Screen resistance measurement

15.1 Installation

15.2 Method

16 Screen leakage current measurement

16.1 Installation

16.2 Method

17 Screen fault current initiation test

17.1 Installation

17.2 Method

18 Operating force test

18.1 Installation

18.2 Method

19 Operating eye test

19.1 Installation

19.2 Method

20 Capacitive test point performance

20.1 Installation

20.2 Test method

Annex A (informative) Determination of the cable conductor temperature

Annex B (informative) Details of the test chamber and spray equipment for humidity and salt fog tests

Bibliography

Figure 1 – Terminations tested in air

Figure 2 – Joints tested in air

Figure 3 – Separable connectors tested in air

Figure 4 – Joints tested under water

Figure 5 – Separable connectors tested under water

Figure 6 – Outdoor terminations tested under water

Figure 7 – Heating cycle

Figure 8 – Typical impact test apparatus for joints

Figure 9 – Test arrangement for the screen leakage current measurement

Figure 10 – Test arrangement for screen fault current initiation test

Figure A.1 – Reference cable

Figure A.2 – Arrangement of the thermocouples

Figure A.3 – Current/temperatures curves

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online