ДСТУ EN 15317:2015 Неразрушающий контроль. Ультразвуковой контроль. Характеристика и верификации оборудования для ультразвуковой толщинометрии (EN 15317:2013, IDT)

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(   
(ДП «УкрНДНЦ»))

Наказ від 24.02.2016 № 52

EN 15317:2013

Non-destructive testing – Ultrasonic testing – Characterization and
verification of ultrasonic thickness measuring equipment

прийнято як національний стандарт
методом «підтвердження» за позначенням
 

ДСТУ EN 15317:2015
 (EN 15317:2013, IDT)

НЕРУЙНІВНИЙ КОНТРОЛЬ
Ультразвуковий контроль. Характеристика і верифікації
обладнання для ультразвукової товщинометрії

З наданням чинності від 2016–01–01

Contents

Foreword

1 Scope

2 Normative references

3 Terms and definitions

4 General requirements for compliance

5 Manufacturer's technical specification for ultrasonic thickness measuring equipment

5.1 General

5.2 General attributes

5.3 Display

5.4 Transmitter

5.5 Receiver

5.6 Other information

6 Calibration blocks

6.1 General

6.2 Material

6.3 Shape and size

6.3.1 Accuracy blocks

6.3.2 Resolution block (see Figure 1)

7 Performance requirements for ultrasonic thickness measuring equipment

8 Probes

9 Group 1 tests

9.1 General

9.2 Equipment required for Group 1 tests

9.3 Stability against temperature

9.3.1 Procedure

9.3.2 Acceptance criterion

9.4 Low battery warning

9.4.1 Procedure

9.4.2 Acceptance criterion

9.5 Battery operational time

9.5.1 Procedure

9.5.2 Acceptance criterion

9.6 Operational voltage range

9.6.1 Procedure

9.6.2 Acceptance criterion

9.7 Operational current range

9.7.1 Procedure

9.7.2 Acceptance criterion

9.8 Operational temperature range

9.8.1 General

9.8.2 Procedure

9.8.3 Acceptance criterion

9.9 Pulse repetition frequency, PRF

9.9.1 Procedure

9.9.2 Acceptance criterion

9.10 Transmitter pulse shape, rise-time and peak voltage

9.10.1 Procedure

9.10.2 Acceptance criterion

9.11 Receiver frequency range of operation

9.11.1 Procedure

9.11.2 Acceptance criterion

9.12 Minimum and maximum measurable thicknesses

9.12.1 Procedure

9.12.2 Acceptance criterion

9.13 Accuracy and resolution

9.13.1 Procedure

9.13.2 Acceptance criterion

9.14 Range of velocity setting (calibration)

9.15 Calibration mechanisms

9.15.1 General

9.15.2 Procedure

9.15.3 Acceptance criterion

9.16 Calibration setting storage

9.16.1 Procedure

9.16.2 Acceptance criterion

9.17 Data storage

9.17.1 Procedure

9.17.2 Acceptance criterion

9.18 Printing

9.18.1 Procedure

9.18.2 Acceptance criterion

9.19 Display and recall

9.19.1 Procedure

9.2 Acceptance criterion

9.20 Display response time 

9.20.1 Procedure

9.20.2 Acceptance criterion

10 Group 2 tests

10.1 General

10.2 Equipment required for Group 2 tests

10.3 General characteristics

10.4 General mechanical state and external aspects

11 Group 3 tests

11.1 General

11.2 General mechanical state and external aspects

11.3 Calibration mechanisms

11.3.1 Procedure

11.3.2 Acceptance criterion

11.4 Calibration setting storage

11.4.1 Procedure

11.4.2 Acceptance criterion

11.5 Data storage

11.5.1 Procedure

11.5.2 Acceptance criterion

Bibliography