ДСТУ EN ISO 19085-1:2018 Деревообрабатывающие станки. Безопасность. Часть 1. Общие требования (EN ISO 19085-1:2017, IDT; ISO 19085-1:2017, IDT)

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(З питань придбання офіційного видання звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ»))

Наказ від 14.06.2018 № 165

EN ISO 19085-1:2017

Woodworking machines — Safety —
Part 1: Common requirements (ISO 19085-1:2017)

прийнято як національний стандарт
методом «підтвердження» за позначенням
Відповідає офіційному тексту

ДСТУ EN ISO 19085-1:2018
(EN ISO 19085-1:2017, IDT; ISO 19085-1:2017, IDT)

Деревообробні верстати. Безпечність.
Частина 1. Загальні вимоги

З наданням чинності від 2018–06–15

 Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 List of significant hazards

5 Safety requirements and measures for controls

5.1 Safety and reliability of control systems

5.2 Control devices

5.3 Start

5.4 Safe stops

5.5 Braking function of tool spindles

5.6 Mode selection

5.7 Spindle speed changing

5.8 Failure of any power supply

5.9 Manual reset control

5.10 Enabling control

5.11 Machine moving parts speed monitoring

5.12 Time delay

6 Safety requirements and measures for protection against mechanical hazards

6.1 Stability

6.2 Risk of break-up during operation

6.3 Fool holder and tool design

6.4 Braking

6.5 Safeguards

6.6 Prevention of access to moving parts

6.7 Impact hazard

6.8 Clamping devices

6.9 Measures against ejection

6.10 Work-piece supports and guides

7 Safety requirements and measures for protection against other hazards

7.1 Fire

7.2 Noise

7.3 Emission of chips and dust

7.4 Electricity

7.5 Ergonomics and handling

7.6 Lighting

7.7 Pneumatics

7.8 Hydraulics

7.9 Electromagnetic compatibility

7.10 Laser

7.11 Static electricity

7.12 Errors of fitting

7.13 Isolation

7.14 Maintenance

8 Information for use

8.1 Warning devices

8.2 Marking

8.3 Instruction handbook

Annex A (informative) Performance level required

Annex В (normative) Test for braking function

Annex C (normative) Stability test for displaceable machines

Annex D (normative) Impact test for guards

Annex E (normative) Noise emission measurement for machines not in ISO 7960:1995

Bibliography

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online