ДСТУ EN ISO 12217-2:2018 Суда малые. Оценка и классификация устойчивости и плавучести. Часть 2. Парусные суда с длиной корпуса, равной или более 6 м (EN ISO 12217-2:2017, IDT; ISO 12217-2:2015, IDT)

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(З питань придбання офіційного видання звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ»))

Наказ від 04.12.2018 № 460

EN ISO 12217-2:2017

Small craft — Stability and buoyancy assessment and categorization —
Part 2: Sailing boats of hull length greater than or equal to 6 m
(ISO 12217-2:2015)

прийнято як національний стандарт
методом «підтвердження» за позначенням
Відповідає офіційному тексту

ДСТУ EN ISO 12217-2:2018
(EN ISO 12217-2:2017, IDT; ISO 12217-2:2015, IDT)

Судна малі. Оцінювання та класифікація стійкості та плавучості.
Частина 2. Парусні судна з довжиною корпусу,
яка дорівнює або більше 6 м

З наданням чинності від 2019-01-01

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

3.1 Primary

3.2 Hazards

3.3 Downflooding

3.4 Dimensions, areas and angles

3.5 Condition, mass and volume

3.6 Other terms and definitions

4 Symbols

5 Procedure

5.1 Maximum load

5.2 Sailing or non-sailing

5.3 Tests, calculations and requirements to be applied

5.4 Variation in input parameters

6 Requirements for monohull boats

6.1 Requirements to be applied

6.2 Downflooding

6.3 Recess size

6.4 Minimum righting energy

6.5 Angle of vanishing stability

6.6 Stability index (STIX)

6.7 Knockdown-recovery test

6.8 Wind stiffness test

6.9 Flotation requirements

6.10 Capsize-recovery test

6.11 Detection and removal of water

7 Requirements for catamarans, trimarans and form-stable monohulls

7.1 Requirements to be applied

7.2 Downflooding openings

7.3 Downflooding height

7.4 Recess size

7.5 Stability information

7.6 Safety signs

7.7 Bare poles factor

7.8 Rolling in breaking waves

7.9 Pitchpoling

7.10 Diagonal stability

7.11 Habitable multihull boats

7.12 Buoyancy when inverted

7.13 Escape after inversion

8 Safety signs

9 Application

9.1 Deciding the design category

9.2 Meaning of the design categories

Annex A (normative) Full method for required downflooding height

Annex В (normative) Methods for calculating downflooding angle

Annex C (normative) Determining the curve of righting moments

Annex D (normative) Method for calculating reserve of buoyancy after inversion or swamping

Annex E (normative) Flotation material and elements

Annex F (normative) Information for owner’s manual

Annex G (normative) Determination of safe wind speed information

Annex H (normative) Determination of longitudinal righting characteristics

Annex I (informative) Summary of requirements

Annex J (informative) Worksheets

Annex К (informative) Illustration of recess retention level

Bibliography

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online