ДСТУ EN ISO 12677:2018 Химический анализ огнеупоров рентгенофлуоресцентным методом (XRF). Метод плавленно-литой капли (EN ISO 12677:2011, IDT; ISO 12677:2011, IDT)
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)
Наказ від 04.12.2018 № 459
EN ISO 12677:2011
Chemical analysis of refractory products
by X-ray fluorescence (XRF) —
Fused cast-bead method (ISO 12677:2011)
прийнято як національний стандарт
методом підтвердження за позначенням
ДСТУ EN ISO 12677:2018
(EN ISO 12677:2011, IDT; ISO 12677:2011, IDT)
Хімічний аналіз вогнетривів
рентгенофлуоресцентним методом (XRF).
Метод плавлено-литої краплі
З наданням чинності від 2019-01-01
Відповідає офіційному тексту
З питань придбання офіційного
видання
звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)
Contents
Foreword
1 Scope
2 Normative references
3 Types of material
4 Principle
5 Apparatus
6 Sample grinding
7 Loss on ignition (and/or drying)
8 Flux
8.1 Choice of flux and ratio of flux to sample
8.2 Compensations for moisture in flux
9 Fusion casting procedures
9.1 Fusion of samples and casting of beads
9.2 Automatic bead preparation
9.3 Storage
9.4 Special problems
10 Calibration
10.1 Calibration standards
10.2 Reagents and series reference materials (SeRMs)
10.3 Calibration using reagents
10.4 Calibration using SeRMs
11 Corrections
11.1 Line-overlap correction
11.2 Background correction
11.3 Drift correction
11.4 Calculation of results
11.5 Software requirements
12 Reproducibility and repeatability
12.1 Fusion tests
12.2 Frequency of instrument tests
12.3 Maximum allowance differences of sample holders
12.4 Sample measuring positions
12.5 Instrument repeatability
12.6 Sequential systems
12.7 Dead time
12.8 Other tests
12.9 Flow gas
13 Accuracy determined by certified reference materials
13.1 Validation of synthetic calibrations .
13.2 Validation of SeRM calibrations
13.3 Fresh beads of the CRMs or synthetic standards used to check SeRM calibrations
14 Definitions of limits of detection
15 Test report
Annex A (normative) Calibration range and required detection limits
Annex B (normative) Corrections for tungsten carbide grinding media
Annex C (informative) Examples of fluxes/flux ratios
Annex D (normative) Examples of CRM to be used to check synthetic calibrations
Annex E (normative) Examples of SeRM
Annex F (normative) Equation for theoretical calculations
Annex G (normative) Certified reference materials (CRMs)
Annex H (normative) Method of inter-element correction used to compensate for the effects of co-existing components when using SeRM for calibration
Annex I (normative) Standard deviations achieved with certified reference materials
Bibliography
Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».