ДСТУ ISO 19702:2018 Руководство по отбору проб и анализу токсичных газов и паров в летучих продуктах сгорания с использованием спектроскопии инфракрасного преобразования Фурье (ИКПФ) (ISO 19702:2015, IDT)

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(З питань придбання офіційного видання звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ»))

Наказ від 10.12.2018 № 473

ISO 19702:2015

Guidance for sampling and analysis of toxic gases
and vapours in fire effluents using Fourier
Transform Infrared (FTIR) spectroscopy

прийнято як національний стандарт
методом «підтвердження» за позначенням
Відповідає офіційному тексту

ДСТУ ISO 19702:2018
(ISO 19702:2015, IDT)

Настанова щодо відбирання проб та аналізування токсичних газів
і парів у летких продуктах згоряння з використанням
спектроскопії інфрачервоного перетворення Фур’є (ІЧПФ)

З наданням чинності від 2019–01–01

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 Principles

5 Sampling

5.1 General

5.2 Temperature of the sampling system

5.3 Filter systems

5.4 Sampling probes

5.5 Sampling line

5.6 Pump selection, position, and flow rate

5.7 Response time of the sampling system

5.8 Optical cell

6 The FTIR spectrophotometer

6.1 Spectrophotometer environment

6.2 Detector

6.3 IR-source

6.4 Mirror alignment and cleanliness

6.5 Spectrophotometer compartment

6.6 Spectral range limits

6.7 Resolution

7 Calibration

7.1 Background noise

7.2 Limits of detection and of quantification (LD and LQ)

7.3 Calibration methods

7.4 Acquiring and collecting calibration standards

8 Measurement procedure

8.1 General

8.2 Daily checks and controls

8.3 Preparation for sampling and analysis

8.4 Initial procedures immediately before a test

8.5 Procedures during sampling from a test

8.6 Procedures after a test

8.7 Data reduction

9 Test report

10 Precision and accuracy

10.1 General

10.2 LD and LQ

10.3 Repeatability and reproducibility

Annex A (informative) FTIR theory

Annex B (informative) FTIR sampling systems

Annex C (informative) Analysis of filter(s), the sampling line and probe for effluent retention

Annex D (normative) Response time determination of the complete FTIR sampling system

Annex E (informative) Considerations for FTIR optical cell selection

Annex F (normative) Verification of FTIR optical cell performance

Annex G (informative) Spectrophotometer

Annex H (normative) Verification of spectrometer performance

Annex I (informative) Reference gases

Annex J (informative) Calibration methods

Annex K (informative) Recording reference spectra and building a calibration set

Annex L (informative) Repeatability and reproducibility

Annex M (informative) Examples of equipment and parameters

Bibliography

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online