ДСТУ EN 61347-2-9:2014 Устройства управления лампами. Часть 2-9. Дополнительные требования к пускорегулирующим устройствам для разрядных ламп (кроме люминесцентных ламп) (EN 61347-2-9:2013, IDT)
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)
Наказ від 29.12.2014 № 1480
Наказ від 27.09.2019 № 299
EN 61347-2-9:2013
Lamp controlgear —
Part 2-9: Particular requirements
for electromagnetic controlgear for discharge lamps
(excluding fluorescent lamps)
прийнято як національний стандарт
методом підтвердження за позначенням
ДСТУ EN 61347-2-9:2014
Пристрої керування лампами.
Частина 2-9. Додаткові вимоги до пускорегулювальних
пристроїв для розрядних ламп
(крім люмінесцентних ламп)
(EN 61347-2-9:2013, IDТ)
З наданням чинності від 2016-01-01
Поновлено чинність від 2019-10-01
Відповідає офіційному тексту
З питань придбання офіційного видання звертайтесь
до національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.org.ua)
Contents
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
4.1 General
4.2 Capacitors and other components
4.3 Thermally protected electromagnetic controlgear
5 General notes on tests
6 Classification
7 Marking
7.1 General
7.2 Mandatory markings
7.3 Information to be provided, if applicable
7.4 Other information
8 Protection against accidental contact with live parts
9 Terminals
10 Provisions for earthing
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings
14 Electromagnetic controlgear heating
14.1 General
14.2 Test requirements
14.3 Normal operating condition
14.4 Abnormal operating condition
15 High-voltage impulse testing
15.1 General
15.2 Test for electromagnetic controlgear operating with lamp with external starting devices
15.3 Test for electromagnetic controlgear operating with lamps with internal starting devices
16 Fault conditions
17 Construction
18 Creepage distances and clearances
19 Screws, current-carrying parts and connections
20 Resistance to heat, fire and tracking
21 Resistance to corrosion
22 No-load output voltage
Annex A (normative) Test to establish whether a conductive part is a live part which may cause an electric shock
Annex B (normative) Particular requirements for thermally protected lamp electromagnetic controlgear
Annex C (normative) Particular requirements for electronic lamp controlgear with means of protection against overheating
Annex D (normative) Requirements for carrying out the heating tests of thermally protected lamp electromagnetic controlgear
Annex E (normative) Use of constant S other than 4500 in tw tests
Annex F (normative) Draught-proof enclosure
Annex G (normative) Explanation of the derivation of the values of pulse voltages
Annex H (normative) Tests
Annex I (normative) Method for selection of varistors
Annex J (informative) Explanation of electromagnetic controlgear temperatures
Annex K (normative) Additional requirements for built-in electromagnetic controlgear with double or reinforced insulation
Bibliography
Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».