ДСТУ EN 62155:2022 Полые керамические и стеклянные изоляторы под давлением и без давления для использования в электрооборудовании с номинальным напряжением свыше 1000 В (EN 62155:2003, IDT; IEC 62155:2003, ID...
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)
Наказ від 28.12.2022 № 285
EN 62155:2003
Hollow pressurized and unpressurized ceramic and glass insulators for use in
electrical equipment with rated voltages greater than 1 000 V
прийнято як національний стандарт
методом «підтвердження» за позначенням
ДСТУ EN 62155:2022
(EN 62155:2003, IDT; IEC 62155:2003, IDT)
Порожнисті керамічні та скляні ізолятори під тиском і без тиску для
використання в електрообладнанні з номінальною напругою понад 1000 В
З наданням чинності від 2023-12-31
Відповідає офіційному тексту
З питань придбання
офіційного видання звертайтесь
до
національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)
CONTENTS
1 Scope and object
1.1 General
1.2 Hollow insulators or hollow insulator bodies intended for general use
1.3 Ceramic hollow insulators intended for use with permanent gas pressure
2 Normative references
3 Terms and definitions
4 Insulating materials
5 General recommendations for design
5.1 General recommendations for design of hollow insulators and hollow insulator bodies intended for general use
5.2 Design rules for hollow insulators and hollow insulator bodies for use with permanent gas pressure
6 Classification of the tests, sampling rules and procedures
6.1 Classification of the tests
6.2 Relevant tests for type, sample and routine tests
6.3 Hollow insulator or hollow insulator body selection
6.4 Retest procedure for sample tests
6.5 Quality assurance
7 General test procedures and requirements
7.1 Verification of the dimensions and roughness of ground surfaces
7.2 Mechanical failing load tests
7.3 Temperature cycle test
7.4 Porosity test
7.5 Galvanizing test
8 Type tests
8.1 Tests
8.2 Pressure test
8.3 Bending test
9 Sample tests
9.1 Tests for hollow insulators or hollow insulator bodies intended for general use
9.2 Tests for ceramic hollow insulators or hollow insulator bodies intended for use with permanent gas pressure
10 Routine tests
10.1 Tests for hollow insulators or hollow insulator bodies intended for general use
10.2 Tests for ceramic hollow insulators or hollow insulator bodies intended for use with permanent gas pressure
10.3 Routine visual inspection
10.4 Electrical routine test
10.5 Routine mechanical tests for hollow insulators or hollow insulator bodies intended for general use
10.6 Routine mechanical tests for ceramic hollow insulators or hollow insulator bodies intended for use with permanent gas pressure
10.7 Routine thermal shock test
11 Documentation
11.1 Marking
11.2 Records
Annex A (informative) Methods of testing for tolerances of parallelism, coaxiality, eccentricity, angular deviation, camber and shed angle of hollow insulators or hollow insulator bodies
Annex B (informative) Methods for bending tests of hollow insulator bodies
Annex C (informative) Alternative test method for the temperature-cycle test
Annex D (informative) Bending moment equivalent to the design pressure
Annex ZA (normative) Normative references to international publications with their corresponding European Publications
Annex ZB (informative) A-deviations
Bibliography
Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».