ДСТУ EN 62052-31:2022 Оборудование для измерения электроэнергии (АС). Общие требования, испытания и условия испытаний. Часть 31. Требования к безопасности продукции и испытания (EN 62052-31:2016, IDT; IEC 620...

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ


ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)

Наказ від 28.12.2022 № 285

EN 62052-31:2016

Electricity metering equipment (AC) - General requirements, tests and
test conditions - Part 31: Product safety requirements and tests

прийнято як національний стандарт
методом «підтвердження» за позначенням

ДСТУ EN 62052-31:2022
(EN 62052-31:2016, IDT;IEC 62052-31:2015, IDT)

Обладнання для вимірювання електроенергії (АС).
Загальні вимоги, випробування та умови випробувань.
Частина 31. Вимоги до безпеки продукції та випробування

З наданням чинності від 2023-12-31

Відповідає офіційному тексту

З питань придбання
офіційного видання звертайтесь до
національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)

CONTENTS

FOREWORD

INTRODUCTION

1 Scope and object

1.1 Scope

1.2 Object

1.3 Verification

1.4 Environmental conditions

2 Normative references

3 Terms and definitions  

3.1 Equipment and states of equipment

3.2 Parts and accessories

3.3 Quantities

3.4 Tests

3.5 Safety terms

3.6 Insulation

3.7 Terms related to switches of metering equipment

4 Tests

4.1 General

4.2 Type test - sequence of tests

4.3 Reference test conditions

4.4 Testing in single fault condition

5 Information and marking requirements

5.1 General

5.2 Labels, signs and signals

5.3 Information for selection

5.4 Information for installation and commissioning

5.5 Information for use

5.6 Information for maintenance

6 Protection against electrical shock

6.1 General requirements

6.2 Determination of accessible parts

6.3 Limit values for accessible parts

6.4 Primary means of protection (protection against direct contact)

6.5 Additional means of protection in case of single fault conditions (protection against indirect contact)

6.6 Connection to external circuits

6.7 Insulation requirements

6.8 Insulation requirements between circuits and parts

6.9 Constructional requirements for protection against electric shock

6.10 Safety related electrical tests

7 Protection against mechanical hazards

7.1 General

7.2 Sharp edges

7.3 Provisions for lifting and carrying

8 Resistance to mechanical stresses

8.1 General

8.2 Spring hammer test

9 Protection against spread of fire

9.1 General

9.2 Eliminating or reducing the sources of ignition within the equipment

9.3 Containment of fire within the equipment, should it occur

9.4 Limited-energy circuit

9.5 Overcurrent protection

10 Equipment temperature limits and resistance to heat

10.1 Surface temperature limits for protection against burns

10.2 Temperature limits for terminals

10.3 Temperatures of internal parts

10.4 Temperature test

10.5 Resistance to heat

11 Protection against penetration of dust and water

12 Protection against liberated gases and substances explosion and implosion -Batteries and battery charging

13 Components and sub-assemblies

13.1 General

13.2 Mains transformers tested outside equipment

13.3 Printed wiring boards

13.4 Components bridging insulation

13.5 Circuits or components used as transient overvoltage limiting devices

14 Hazards resulting from application - Reasonably foreseeable misuse

15 Risk assessment

Annex A (normative) Measuring circuits for touch current

Annex B (informative) Examples for insulation between parts

Annex C (informative) Examples for direct connected meters equipped with supply control and load control switches

Annex D (normative) Test circuit diagram for the test of long term overvoltage withstand

Annex E (normative) Test circuit diagram for short current test on the current circuit of direct connected meters

Annex F (informative) Examples for voltage tests

Annex G (normative) Additional a.c. voltage tests for electromechanical meters

Annex H (normative) Test equipment for cable flexion and pull test

Annex I (informative) Routine tests

Annex J (informative) Examples of battery protection

Annex K (informative) Rationale for specifying overvoltage category III

Annex L (informative) Overview of safety aspects covered

Annex M (informative) Index of defined terms

Bibliography

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online