ДСТУ EN ISO/IEC 17043:2014 Оценка соответствия. Общие требования к проверке квалификации лабораторий (EN ISO/IEC 17043:2010, IDT)

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Наказом Міністерства економічного розвитку і торгівлі України від 30.12.2014 № 1494

EN ISO/IEC 17043:2010

en: Conformity assessment - General requirements for proficiency testing (ISO/IEC 17043:2010)

прийнято як національний стандарт методом «підтвердження» за позначенням
Відповідає офіційному тексту

ДСТУ EN ISO/IEC 17043:2014

uk: Оцінка відповідності. Загальні вимоги до перевірки кваліфікації лабораторій (EN ISO/IEC 17043:2010, IDT)

З наданням чинності від 2016-01-01

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM

ICS 03.120.20

EN ISO/IEC 17043

February 2010

English version

Conformity assessment - General requirements for proficiency testing (ISO/CASCO 17043:2010)

Évaluation de la conformité - Exigences générales concernant les essais d’aptitude (ISO/CASCO 17043:2010)

Konformitätsbewertung - Allgemeine Anforderungen an Eignungsprüfungen (ISO/CASCO 17043:2010)

This European Standard was approved by CEN on 30 January 2010.

CEN and CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN and CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN and CENELEC member into its own language and notified to the CEN Management Centre has the same status as the official versions.

CEN and CENELEC members are the national standards bodies and national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

CEN Management Centre: Avenue Marnix 17, B-1000 Brussels

CENELEC Central Secretariat: Avenue Marnix 17, B-1000 Brussels

Foreword

This document (EN ISO/IEC 17043:2010) has been prepared by Technical Committee ISO/CASCO «Committee on conformity assessment» in collaboration with Technical Committee CEN/CLC/TC 1 «Criteria for conformity assessment bodies», the secretariat of which is held by BSI.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2010, and conflicting national standards shall be withdrawn at the latest by August 2010.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

Endorsement notice

The text of ISO/CASCO 17043:2010 has been approved by CEN as a EN ISO/IEC 17043:2010 without any modification.

INTERNATIONAL ISO/IEC STANDARD 17043

First edition 2010-02-01

Conformity assessment – General requirements for proficiency testing

Évaluation de la conformité – Exigences générales concernant les essais d’aptitude

Foreword

ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of conformity assessment, the ISO Committee on conformity assessment (CASCO) is responsible for the development of International Standards and Guides.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

Draft International Standards are circulated to the national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO/IEC 17043 was prepared by the ISO Committee on conformity assessment (CASCO).

It was circulated for voting to the national bodies of both ISO and IEC, and was approved by both organizations.

This first edition of ISO/IEC 17043 cancels and replaces ISO/IEC Guide 43-1:1997 and ISO/IEC Guide 43-2:1997, which have been technically revised.

Introduction

Interlaboratory comparisons are widely used for a number of purposes and their use is increasing internationally. Typical purposes for interlaboratory comparisons include:

a) evaluation of the performance of laboratories for specific tests or measurements and monitoring laboratories’ continuing performance;

b) identification of problems in laboratories and initiation of actions for improvement which, for example, may be related to inadequate test or measurement procedures, effectiveness of staff training and supervision, or calibration of equipment;

c) establishment of the effectiveness and comparability of test or measurement methods;

d) provision of additional confidence to laboratory customers;

e) identification of interlaboratory differences;

f) education of participating laboratories based on the outcomes of such comparisons;

g) validation of uncertainty claims;

h) evaluation of the performance characteristics of a method - often described as collaborative trials;

i) assignment of values to reference materials and assessment of their suitability for use in specific test or measurement procedures; and

j) support for statements of the equivalence of measurements of National Metrology Institutes through «key comparisons» and supplementary comparisons conducted on behalf of the International Bureau of Weights and Measurement (BIPM) and associated regional metrology organizations.

Proficiency testing involves the use of interlaboratory comparisons for the determination of laboratory performance, as listed in a) to g) above. Proficiency testing does not usually address h), i) and j) because laboratory competence is assumed in these applications, but these applications can be used to provide independent demonstrations of laboratory competence. The requirements of this International Standard can be applied to many of the technical planning and operational activities for h), i) and j).

The need for ongoing confidence in laboratory performance is not only essential for laboratories and their customers but also for other interested parties, such as regulators, laboratory accreditation bodies and other organizations that specify requirements for laboratories. ISO/IEC 17011 requires accreditation bodies to take account of laboratories’ participation and performance in proficiency testing. There is a growing need for proficiency testing for other conformity assessment activities, such as inspection or product certification. Most of the requirements in this International Standard apply to those evolving areas, especially regarding management, planning and design, personnel, assuring quality, confidentiality, and other aspects, as appropriate.

This International Standard has been prepared to provide a consistent basis for all interested parties to determine the competence of organizations that provide proficiency testing. In doing so it replaces both parts of ISO/IEC Guide 43:1997. ISO/IEC Guide 43 included not only guidance on development and operation of proficiency testing and selection and use of proficiency testing by laboratory accreditation bodies, but also useful descriptions of typical types of proficiency testing. This International Standard has preserved and updated the principles for the operation of proficiency testing described in ISO/IEC Guide 43 and has retained in Annexes A to C information on typical types of proficiency testing schemes, guidance on appropriate statistical methods, selection and use of proficiency testing schemes by laboratories, accreditation bodies, regulatory bodies, and other interested parties.

INTERNATIONAL STANDARD ISO/IEC 17043 :2010(E)

Conformity assessment – General requirements for proficiency testing

1 Scope

This International Standard specifies general requirements for the competence of providers of proficiency testing schemes and for the development and operation of proficiency testing schemes. These requirements are intended to be general for all types of proficiency testing schemes, and they can be used as a basis for specific technical requirements for particular fields of application.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

ISO/IEC 17000:2004, Conformity assessment – Vocabulary and general principles

ISO/IEC Guide 99:2007, International vocabulary of metrology – Basic and general concepts and associated terms (VIM)

3 Terms and definitions

For the purposes of this document, the terms and definitions given in ISO/IEC 17000:2004, ISO/IEC Guide 99:2007 and the following apply.

3.1 assigned value

value attributed to a particular property of a proficiency test item

3.2 coordinator

one or more individuals with responsibility for organizing and managing all of the activities involved in the operation of a proficiency testing scheme

3.3 customer

organization or individual for which a proficiency testing scheme is provided through a contractual arrangement

3.4 interlaboratory comparison

organization, performance and evaluation of measurements or tests on the same or similar items by two or more laboratories in accordance with predetermined conditions

3.5 outlier

observation in a set of data that appears to be inconsistent with the remainder of that set

NOTE An outlier can originate from a different population or be the result of an incorrect recording or other gross error.

3.6 participant

laboratory, organization or individual that receives proficiency test items and submits results for review by the proficiency testing provider

NOTE In some cases, the participant can be an inspection body.

3.7 proficiency testing

evaluation of participant performance against pre-established criteria by means of interlaboratory comparisons

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online