ДСТУ EN ISO 23125:2016 Станки. Безопасность. Токарные станки (EN ISO 23125:2015, IDT; ISO 23125:2015, IDT)

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(З питань придбання офіційного видання звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ»))

Наказ від 08.07.2016 № 204
Наказ від 28.12.2019 № 526

EN ISO 23125:2015

Machine tools — Safety — Turning machines
(ISO 23125:2015, Corrected version 2016-03-15)

прийнято як національний стандарт
методом «підтвердження» за позначенням
Відповідає офіційному тексту

ДСТУ EN ISO 23125:2016
(EN ISO 23125:2015, IDT; ISO 23125:2015, IDT)

Верстати. Безпека. Токарні верстати

З наданням чинності від 2016–07–13
Поновлено чинність від 2020–01–01

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

3.1 General terms

3.2 Terms related to parts of turning machines

3.3 Terms related to modes of operation — Mandatory and optional modes of operation for turning machines

3.4 Terms related to sizes and groups of turning machines defined

3.5 Terms related to maximum permissible spindle speeds and axes feeds

4 List of significant hazards

4.1 General

4.2 Main hazard zones

4.3 Significant hazards and hazardous situations covered by this International Standard

5 Safety requirements and/or protective measures

5.1 General requirements

5.2 Specific requirements resulting from mechanical hazards identified in Clause 4

5.3 Specific requirements resulting from electrical hazards

5.4 Specific requirements resulting from noise hazards

5.5 Specific requirements resulting from radiation hazards

5.6 Specific requirements resulting from material or substance hazards

5.7 Specific requirements resulting from neglect of ergonomic principles hazards

5.8 Specific requirements resulting from unexpected start-up, over-run or over-speed hazards

5.9 Specific requirements resulting from variation in rotational speed of tool hazards

5.10 Specific requirements resulting from failure of the power supply hazards

5.11 Specific requirements resulting from failure of the control circuit hazards

5.12 Specific requirements resulting from errors of fitting hazards

5.13 Specific requirements resulting from ejected fluids or objects hazards

5.14 Specific requirements resulting from loss of stability hazards

5.15 Specific requirements resulting from slips, trips and fall of persons hazards

5.16 Verification of the safety requirements and/or protective measures

6 Information for use

6.1 Marking

6.2 Instruction for use

Annex A (normative) Impact test method for guards on turning machines

Annex B (informative) Test equipment for impact test and examples of materials

Annex C (informative) Calculation of direct impact energy

Annex D (informative) Example of checklist for safety functions

Annex E (informative) Examples of exhaust and extinguishing systems

Annex F (informative) Example of the determination of performance level for interlocked guard

Bibliography

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online