ДСТУ EN 334:2015 Регуляторы давления газа для входного давления до 100 бар (EN 334:2005+A1:2009, IDT)

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство «Український науково-дослідний і навчальний
центр проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)

Наказ від 25.12.2015 № 207
(у редакції наказу від 20.05.2016 № 137)

EN 334:2005+A1:2009

Gas pressure regulators for inlet pressures up to 100 bar

прийнято як національний стандарт
методом «підтвердження» за позначенням

ДСТУ EN 334:2015
(EN 334:2005+A1:2009, IDT)

Регулятори тиску газу для вхідного тиску до 100 бар

З наданням чинності від 2016–01–01

Відповідає офіційному тексту

З питань придбання офіційного видання звертайтесь до
 національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.org.ua) 

Contents

Foreword

1 Scope

2 Normative references

3 Terms, definitions and symbols

3.1 General terms and definitions of types of gas pressure regulators

3.2 Terms and definitions of components of gas pressure regulators

3.3 Terms, symbols and definitions of components of functional performance

3.4 Terms, symbols and definitions related to design and tests

4 Construction requirements

4.1 Basic requirements

4.2 Materials

4.3 Strength of housings

5 Functional requirements

5.1 General

5.2 Shell strength, external tightness and internal sealing

5.3 Control classifications

5.4 Final visual inspection

5.5 Fail-close conditions

6 Gas pressure regulator sizing

6.1 Flow behaviour

6.2 Sizing equations for the calculation of volumetric flow rates of a gas pressure regulator with its control member in its mechanically fully open position

6.3 Calculation of the maximum accuracy flow rate

6.4 Inherent flow characteristics

6.5 Calculation of volumetric flow rates for partially open gas pressure regulators

6.6 Flow coefficient

7 Testing

7.1 General

7.2 Tests

7.3 Type test

7.4 Selection of test samples

7.5 Routine tests

7.6 Production surveillance .

7.7 Test and verification methods

8 Documentation

8.1 Documentation related to type test

8.2 Documentation related to the routine tests

8.3 Documentation related to production surveillance in accordance with 7.6

9 Marking

9.1 General requirements

9.2 Markings for the various connections

9.3 Marking of integrated safety devices

Annex A (informative) Alternative methods for the determination of the accuracy class, the lock- up pressure class, the maximum accuracy flow rate, the flow coefficients and the verification of the hysteresis band

Annex B (informative) Inspection certificate

Annex C (informative) Acceptance test

Annex D (informative) Compliance evaluation)

Annex E (informative) Seat leakage (alternative requirement)

Annex F (normative) Creep (venting) relief device

Annex G (informative) Order specification

Annex H (normative) Materials

Annex I (informative) Glossary

Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC

Bibliography

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online