ДСТУ EN 13476-3:2022 Системы пластмассовых трубопроводов для подземной и безнапорной канализации. Системы трубопроводов со структурированными стенками из непластифицированного поливинилхлорида (PVC-U), полипр...
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)
Наказ від 01.11.2022 № 220
EN 13476-3:2018+А1:2020
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems
of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3:
Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B
прийнято як національний стандарт
методом «підтвердження» за позначенням
ДСТУ EN 13476-3:2022
(EN 13476-3:2018+А1:2020, IDT)
Системи пластмасових трубопроводів для підземної та безнапірної каналізації. Системи трубопроводів
зі структурованими стінками з не пластифікованого полівінілхлориду (PVC-U), поліпропілену (РР) та
поліетилену (РЕ). Частина 3. Технічні умови на труби і фітинги з гладкою внутрішньою та
профільованою зовнішньою поверхнями типу В
З наданням чинності від 2022-11-10
Відповідає офіційному тексту
З питань придбання офіційного видання звертайтесь
до національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)
Contents
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions
3.2 Symbols
3.3 Abbreviations
4 Material
4.1 General
4.2 Unplasticized poly(vinyl chloride) (PVC-U)
4.3 Polypropylene (PP)
4.4 Polyethylene (PE)
4.5 Sealing rings
4.6 Fused or welded joints
4.7 Adhesives for PVC-U
5 Designation of wall constructions and examples of typical jointing methods
5.1 Wall constructions designated as Type В
5.2 Designation and design of joints
6 Appearance and colour
7 Geometrical characteristics
7.1 General
7.2 Dimensions
7.3 Types of fittings
7.4 Design length of fittings
8 Physical characteristics
8.1 Unplastisized poly(vinyl chloride) (PVC-U)
8.2 Polypropylene (PP)
8.3 Polyethylene (PE)
9 Mechanical characteristics
9.1 Mechanical characteristics of pipes
9.2 Mechanical characteristics of fittings
10 Performance requirements
11 Marking
11.1 General
11.2 Minimum required marking
11.3 Additional marking
Annex A (normative) Compound / formulation PVC-U material
Annex В (normative) Utilization of non-virgin PVC-U material
Annex C (normative) Compound / Formulation PP material
Annex D (normative) Utilization of non-virgin PP material
Annex E (normative) Compound / Formulation PE material
Annex F (normative) Utilization of non-virgin PE material
Annex G (normative) Impact test at 23 °С
Annex H (normative) Impact test at -10 °С
Annex I (normative) Ring flexibility test at 20 % diametric deflection
Annex J (informative) Survey of possible use of reprocessed and recycled material
Annex К (normative) Impact test for large diameter pipes with structured wall
Bibliography
Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».