ДСТУ EN 60939-2:2022 Пасивні фільтрувальні блоки для притлумлення електромагнітних перешкод. Частина 2. Специфікації підрозділу. Пасивні фільтрувальні блоки, для яких доцільно перевірити безпеку. Методи тесту...
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)
Наказ від 28.12.2022 № 285
EN 60939-2:2005
Passive filter units for electromagnetic interference
suppression - Part 2: Sectional
specification: Passive filter units for which safety tests
are appropriate - Test methods
and general requirements
прийнято як національний стандарт
методом «підтвердження» за позначенням
ДСТУ EN 60939-2:2022
(EN 60939-2:2005, IDT; IEC 60939-2:2005, IDT)
Пасивні фільтрувальні блоки для притлумлення
електромагнітних перешкод.
Частина 2. Специфікації підрозділу. Пасивні фільтрувальні
блоки, для яких
доцільно перевірити безпеку. Методи тестування та загальні
вимоги
З наданням чинності від 2023-12-31
Відповідає офіційному тексту
З питань придбання
офіційного видання звертайтесь
до
національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)
CONTENTS
1 General
1.1 Scope
1.2 Normative references
1.3 Information to be given in a detail specification
1.4 Terms and definitions
1.5 Marking
2 Preferred ratings and characteristics
2.1 Preferred characteristics
2.2 Preferred values of ratings
3 Quality assessment procedures
3.1 Primary stage of manufacture
3.2 Structurally similar filters
3.3 Certified records of released lots
3.4 Approval testing
3.5 Quality conformance inspection
4 Test and measurement procedures
4.1 Earth inductors incorporated in filters
4.2 Capacitance and tan δ measurements
4.3 Visual examination and check of dimensions
4.4 Voltage proof
4.5 Insulation resistance
4.6 DC line resistance or voltage drop at rated current
4.7 Insertion loss
4.8 Discharge resistance
4.9 Robustness of terminations
4.10 Resistance to soldering heat
4.11 Solderability
4.12 Rapid change of temperature
4.13 Vibration
4.14 Bump
4.15 Shock
4.16 Container sealing
4.17 Climatic sequence
4.18 Damp heat, steady state
4.19 Temperature rise
4.20 Impulse voltage
4.21 Endurance
4.22 Charge and discharge
4.23 Passive flammability
4.24 Current overload
4.25 Solvent resistance of the marking
4.26 Component solvent resistance
4.27 Active flammability
Annex A (normative) Test schedule for qualification approval – Assessment level D / DZ
Annex B (normative) Test schedule for safety requirements only
Annex C (normative) Circuit for the impulse voltage test
Annex D (normative) Circuit for the endurance test
Annex E (normative) Declaration of design
Annex ZA (normative) Normative references to international publications with their corresponding European publications
Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».