ДСТУ EN 16474:2016 Машини для виробництва гумових та пластмасових виробів. Машини для вулканізації покришок. Вимоги щодо безпеки (EN 16474:2015, IDT)

Даний документ доступний у тарифі «ВСЕ ВРАХОВАНО»

У Вас є питання стосовно документа? Ми раді на них відповісти!Перелік безкоштовних документівПомітили помилку в документі або на сайті? Будь ласка, напишіть нам про це!Залишити заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(З питань придбання офіційного видання звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ»))

Наказ від 08.07.2016 № 204

EN 16474:2015

Plastics and rubber machines —
Tyre curing machines — Safety requirements

прийнято як національний стандарт
методом «підтвердження» за позначенням
Відповідає офіційному тексту

ДСТУ ЕN 16474:2016
(EN 16474:2015, IDT)

Машини для виробництва гумових та пластмасових виробів.
Машини для вулканізації покришок. Вимоги щодо безпеки

З наданням чинності від 2016-07-13

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 List of significant hazards

4.1 General

4.2 General hazards

4.3 Hazards associated with specific machine parts or areas

5 Safety requirements and/or protective measures

5.1 General safety requirements and/or protective measures

5.2 Specific safety requirements and/or protective measures

5.2.1 Specific requirements for operation in production mode

5.2.2 Specific requirements for operations other than the production mode

5.2.3 Specific requirements for tyre curing machines with two cavities and independent curing cycles and independent safeguarding

5.3 Emergency stop function

5.4 Requirements for noise reduction

5.4.1 Main noise sources

5.4.2 Noise reduction at source by design

5.4.3 Noise reduction by protective measures

5.4.4 Information connected with noise hazards

6 Verification of the safety requirements and/or protective measures

7 Information for use

7.1 General

7.2 Instruction handbook

7.2.1 General

7.2.2 Exhaust system

7.2.3 Leakage of nitrogen

7.2.4 Hazards due to hot surfaces

7.2.5 Leakage of curing media from hoses and pipes

7.2.6 Non-permanent safe means of access

7.2.7 Maintenance operations

7.2.8 Fixation of the upper part of the container or mould

7.2.9 Machine parameters

7.2.10 Emergency stop and fluid discharge

7.2.11 Noise emission

7.3 Marking

7.4 Warning signs

Annex A (normative) Noise test code

A.1 Introduction

A.2 Measurement of the A-weighted emission sound pressure level at the operator’s or other specified positions

A.2.1 Basic standards

A.2.2 Measurement procedure

A.2.3 Measurement uncertainty

A.3 Installation, mounting and operating conditions for noise emission measurement

A.4 Information to be recorded and reported

A.5 Declaration and verification of noise emission values

Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC

Bibliography

Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».

Увійти в Особистий кабінет Детальніше про тарифи

БУДСТАНДАРТ Online