ДСТУ EN ISO 21809-5:2018 Нафтова та газова промисловість. Зовнішні покриви підземних або підводних трубопроводів у трубопровідних транспортних системах. Частина 5. Зовнішні бетонні покриви (EN ISO 21809-5:201...
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(З питань придбання офіційного видання звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ»))
Наказ від 27.02.2018 № 65
EN ISO 21809-5:2017
Petroleum and natural gas industries —
External coatings for buried or submerged pipelines used
in pipeline transportation systems —
Part 5: External concrete coatings (ISO 21809-5:2017)
прийнято як національний стандарт
методом «підтвердження» за позначенням
Відповідає офіційному тексту
ДСТУ EN ISO 21809-5:2018
(EN ISO 21809-5:2017, IDT; ISO 21809-5:2017, IDT)
Нафтова та газова промисловість.
Зовнішні покриви підземних або підводних трубопроводів
у трубопровідних транспортних системах.
Частина 5. Зовнішні бетонні покриви
З наданням чинності від 2018–04–01
Contents
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
4.1 Symbols
4.2 Abbreviated terms
5 General requirements
5.1 Rounding
5.2 Compliance with this document
6 Information supplied by the purchaser
6.1 General information
6.2 Additional information
7 Materials
7.1 Pipe
7.2 Cement
7.3 Supplementary cementitious materials
7.4 Aggregate — Fine and coarse
7.5 Heavyweight aggregate
7.6 Lightweight aggregate
7.7 Recycled concrete as aggregate
7.8 Water
7.9 Steel reinforcement
7.10 Concrete admixtures
7.11 Reclaimed concrete
8 Concrete mix
9 Coating application
9.1 Qualification
9.2 Application of concrete coating
9.3 Environmental conditions
9.4 Pipe
9.4.1 Pre-coated pipe
9.4.2 Bare pipe
9.5 Steel reinforcement
9.5.1 General
9.5.2 Cage reinforcement
9.5.3 Welded wire mesh reinforcement
9.5.4 Woven wire mesh reinforcement
9.5.5 Reinforcement placement
9.6 Concrete cutback
9.7 Anode installation
10 Curing methods
11 Inspection and testing
11.1 General
11.2 Test procedures
11.2.1 Concrete coating thickness — Diameter measurement
11.2.2 Placement of reinforcement
11.2.3 Pre-concrete coated pipe weight in air
11.2.4 Concrete coated pipe weight in air
11.2.5 Concrete coating density
11.2.6 Compressive strength
11.2.7 Water absorption
11.2.8 Impact resistance
11.2.9 Shear resistance
11.2.10 Visual inspection
11.3 Retesting
11.4 Test results
12 Repair of concrete coated pipe
12.1 General
12.2 Damaged areas
12.3 Cracks
12.4 Gaps
12.5 Stripping
13 Markings
14 Handling and storage
15 Test reports and inspection documents
Annex A (normative) Water absorption test
Annex B (normative) Shear resistance test
Bibliography
Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».