ДСТУ EN ISO 5659-2:2018 Пластмаси. Димоутворювальна здатність. Частина 2. Визначення оптичної густини під час випробування в однокамерній шафі (EN ISO 5659-2:2017, IDT; ISO 5659-2:2017, IDT)
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)
Наказ від 10.12.2018 № 473
EN ISO 5659-2:2017
Plastics — Smoke generation —
Part 2: Determination of optical density
by a single-chamber test (ISO 5659-2:2017)
прийнято як національний стандарт
методом підтвердження за позначенням
ДСТУ EN ISO 5659-2:2018
(EN ISO 5659-2:2017, IDT; ISO 5659-2:2017, IDT)
Пластмаси. Димоутворювальна здатність.
Частина 2. Визначення оптичної густини
під час випробування в однокамерній шафі
З наданням чинності від 2019–01–01
Відповідає офіційному тексту
З питань придбання
офіційного видання звертайтесь
до
національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.org.ua)
Contents
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principles of the test
5 Suitability of a material or product for testing
5.1 Material or product geometry
5.2 Surface characteristics
5.3 Asymmetrical products
6 Specimen construction and preparation
6.1 Number of specimens
6.2 Size of specimens
6.3 Specimen preparation
6.4 Conditioning
6.5 Wrapping of specimens
7 Apparatus and ancillary equipment
7.1 General
7.2 Test chamber
7.3 Specimen support and heating arrangements
7.4 Gas supply
7.5 Photometric system
7.6 Chamber leakage
7.7 Cleaning materials
7.8 Ancillary equipment
8 Test environment
9 Setting-up and calibration procedures
9.1 General
9.2 Alignment of photometric system
9.3 Selection of compensating filter(s)
9.4 Linearity check
9.5 Calibration of range-extension filter
9.6 Chamber leakage rate test
9.7 Burner calibration
9.8 Radiator cone calibration
9.9 Cleaning
9.10 Frequency of checking and calibrating procedure
10 Test procedure
10.1 General
10.2 Preparation of test chamber
10.3 Tests with pilot flame
10.4 Preparation of the photometric system
10.5 Loading the specimen
10.6 Recording of light transmission
10.7 Observations
10.8 Termination of test
10.9 Testing in different modes
11 Expression of results
11.1 Specific optical density, Ds
11.2 Clear-beam correction factor, Dc
12 Precision
13 Test report
Annex A (normative) Calibration of heat flux meter
Annex В (informative) Variability in the specific optical density of smoke measured in the single-chamber test
Annex C (informative) Determination of mass optical density
Annex D (informative) Precision data from tests on intumescent materials
Annex E (informative) Guidance on optical density testing
Annex F (informative) Specific sample preparation
Bibliography
Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».