ДСТУ ISO 5660-1:2018 Випробування щодо реакції на вогонь. Швидкість тепловиділення, димоутворення та втрати маси. Частина 1. Визначення швидкості тепловиділення методом конусного калориметра та швидкості димо...
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості» (ДП «УкрНДНЦ»)
Наказ від 10.12.2018 № 473
ISO 5660-1:2015
Reaction-to-fire tests - Heat release,
smoke production and mass loss rate -
Part 1: Heat release rate (cone calorimeter method)
and smoke production rate (dynamic measurement)
прийнято як національний стандарт
методом підтвердження за позначенням
ДСТУ ISO 5660-1:2018
(ISO 5660-1:2015, IDT)
Випробування щодо реакції на вогонь.
Швидкість тепловиділення, димоутворення та втрати маси.
Частина 1. Визначення швидкості тепловиділення
методом конусного калориметра та швидкості
димоутворення динамічними вимірюваннями
З наданням чинності від 2019-01-01
Відповідає офіційному тексту
З питань придбання офіційного видання звертайтесь
до національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)
Contents
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Principle
6 Apparatus
6.1 General
6.2 Cone-shaped radiant electrical heater
6.3 Radiation shield
6.4 Irradiance control
6.5 Weighing device
6.6 Specimen holder
6.7 Retainer frame
6.8 Exhaust gas system with flow measuring instrumentation
6.9 Gas sampling apparatus
6.10 Ignition circuit
6.11 Ignition timer
6.12 Oxygen analyser
6.13 Heat flux meters
6.14 Calibration burner
6.15 Data collection and analysis system
6.16 Optional side screens
6.17 Smoke obscuration measuring system
6.18 Smoke system thermocouple
6.19 Optical filters
7 Suitability of a product for testing
7.1 Surface characteristics
7.2 Asymmetrical products
7.3 Materials of short burning time
7.4 Composite specimens
7.5 Dimensionally unstable materials
7.6 Materials that require testing under compression
8 Specimen construction and preparation
8.1 Specimens
8.2 Conditioning of specimens
8.3 Preparation
9 Test environment
10 Calibration
10.1 Preliminary calibrations
10.2 Operating calibrations
10.3 Smoke meter calibration
10.4 Less frequent calibrations
11 Test procedure
11.1 General precautions
11.2 Initial preparation
11.3 Procedure
12 Calculations
12.1 General
12.2 Calibration constant for oxygen consumption analysis
12.3 Heat release rate
12.4 Exhaust duct flow rate
12.5 Mass loss rate
12.6 Smoke obscuration
13 Test report
Annex A (informative) Commentary and guidance notes for operators
Annex B (informative) Supplementary calculations - Normalization to the mass loss rate of the specific extinction area of specimen
Annex C (informative) Resolution, precision and bias
Annex D (informative) Mass loss rate and effective heat of combustion
Annex E (informative) Testing in the vertical orientation
Annex F (informative) Calibration of the working heat flux meter
Annex G (informative) Calculation of heat release with additional gas analysis
Annex H (informative) Calculation of Effective Critical Heat Flux for Ignition
Bibliography
Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».