ДСТУ EN ISO 15494:2019 Системи пластмасових трубопроводів промислового призначення. Полібутен (PB), поліетилен (PE), поліетилен підвищеної термостійкості (PE-RT), сітчастий поліетилен (PE-X) та поліпропілен (...
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)
Наказ від 26.12.2019 № 505
EN ISO 15494:2018
Plastics piping systems for industrial applications —
Polybutene (PB), polyethylene (PE),
polyethylene
of raised temperature resistance (PE-RT),
crosslinked polyethylene (PE-X), polypropylene (PP) —
Metric series for specifications for components and the system
(ISO 15494:2015)
прийнято як національний стандарт
методом підтвердження за позначенням
ДСТУ EN 130 15494:2019
(EN ISO 15494:2018, IDT;
ISO 15494:2015, IDT)
Системи пластмасових трубопроводів
промислового призначення.
Полібутен (РВ), поліетилен (РЕ),
поліетилен підвищеної термостійкості (PE-RT),
сітчастий поліетилен (РЕ-Х) та поліпропілен (РР).
Технічні умови на компоненти та систему. Метрична серія
З наданням чинності від 2020-01-01
Відповідає офіційному тексту
З питань придбання
офіційного видання звертайтесь
до
національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.org.ua)
Contents
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 Geometrical definitions
3.2 Material definitions
3.3 Definitions related to material characteristics
3.4 Definitions related to service conditions
4 Symbols and abbreviated terms
4.1 Symbols
4.2 Abbreviated terms
5 Material
5.1 General
5.2 Hydrostatic strength properties
5.3 Material characteristics
5.4 Reprocessable and recyclable material
5.5 Materials for components not made from PB, PE, PE-RT, PE-X, or PP
6 General characteristics
6.1 Appearance
6.2 Colour
6.3 Influence of UV radiation
7 Geometrical characteristics
7.1 General
7.2 Mean outside diameters, out-of-roundness (ovality), and tolerances
7.3 Wall thicknesses and related tolerances
7.4 Angles
7.5 Laying lengths
7.6 Threads
7.7 Mechanical fittings
7.8 Joint dimensions of valves
8 Mechanical characteristics
8.1 Resistance to internal pressure of components
8.2 Calculation of the test pressure for components
9 Physical characteristics
10 Chemical characteristics
10.1 Effects on the component material(s)
10.2 Effects on the fluids
11 Electrical characteristics
12 Performance requirements
12.1 General
12.2 Fusion compatibility
13 Classification of components
14 Design and installation
15 Declaration of conformity
16 Marking
16.1 General
16.2 Minimum required marking of pipes
16.3 Minimum required marking of fittings
16.4 Minimum required marking of valves
Annex A (normative) Specific characteristics and requirements for industrial piping systems made from polybutene (PB)
Annex В (normative) Specific characteristics and requirements for industrial piping systems made from polyethylene (PE)
Annex C (normative) Specific characteristics and requirements for industrial piping systems made from polyethylene of raised temperature resistance (PE-RT)
Annex D (normative) Specific characteristics and requirements for industrial piping systems made from crosslinked polyethylene (PE-X)
Annex E (normative) Specific characteristics and requirements for industrial piping systems made from polypropylene (PP) .
Annex F (informative) Design and installation
Bibliography
Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».