ДСТУ EN 61000-4-12:2012 Електромагнітна сумісність. Частина 4-12. Методики випробування та вимірювання. Випробування на несприйнятливість до неповторюваних загасних коливних перехідних процесів (EN 61000-4-12...

Даний документ доступний у тарифі «ВСЕ ВРАХОВАНО»

У Вас є питання стосовно документа? Ми раді на них відповісти!Перелік безкоштовних документівПомітили помилку в документі або на сайті? Будь ласка, напишіть нам про це!Залишити заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Наказом Міністерства економічного розвитку і торгівлі України
від 28.05.2012 № 640

Європейський стандарт

EN 61000-4-12:2006

en:  Electromagnetic compatibility (EMC)
Part 4-12: Testing and measurement techniques - Ring wave immunity test

прийнято як національний стандарт методом «підтвердження»
мовою оригіналу за національним позначенням

ДСТУ EN 61000-4-12:2012

uk:  Електромагнітна сумісність. Частина 4-12. Методики випробування
та вимірювання. Випробування на несприйнятливість до неповторюваних
загасних коливних перехідних процесів
(EN 61000-4-12:2006, IDT
)

З наданням чинності в Україні від 2012-08-01

Contents

Introduction

1 Scope

2 Normative references

3 Terms and definitions6

4 General

4.1 Description of the phenomenon

4.2 Relevant parameters

5 Test levels

6 Test equipment

6.1 Test generator

6.2 Coupling/decoupling network specifications

7 Test set-up

7.1 Test of power supply ports

7.2 Test of input/output ports

7.3 Test of communication ports

7.4 Earthing connections

7.5 Equipment under test

7.6 Coupling/decoupling networks

8 Test procedure

8.1 Laboratory reference conditions

8.2 Execution of the test

9 Evaluation of test results

10 Test report

Annex A (informative)  Information on test levels for the ring wave

Bibliography

Annex ZA (normative)  Normative references to international publications with their corresponding European publications

Figure 1 – Waveform of the ring wave (open circuit voltage and short circuit current)

Figure 2 – Example of schematic circuit of the test generator for ring wave

Figure 3 – Example of test set-up for table-top equipment using the ground reference plane

Figure 4 – Example of test set-up for floor-standing equipment using the ground reference plane

Figure 5 – AC/DC power supply port, single phase, line-to-line test

Figure 6 – AC/DC power supply port, single phase, line-to-ground test

Figure 7 – Example of test setup for capacitive coupling on a.c. lines (3 phases) – line L3 to line L1 coupling

Figure 8 – Example of test setup for capacitive coupling on a.c. lines (3 phases) – line L3 to ground coupling

Figure 9 – Example of test setup for unshielded unsymmetrical interconnection lines – line-to-line and line-to-ground coupling via capacitors

Figure 10 – Example of test setup for unshielded unsymmetrical interconnection lines – line-to-line and line-to-ground coupling via arrestors

Figure 11 – Example of test setup for unshielded unsymmetrical interconnection lines – line-to-line and line-to-ground coupling via a clamping circuit

Figure 12 – Example of test setup for unshielded symmetrical interconnection lines (communication lines) – lines-to-ground coupling via arrestors

Figure 13 – Test of a system with communication ports with fast operating signals (generator output earthed)

Table 1 – Test levels for ring wave

Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».

Увійти в Особистий кабінет Детальніше про тарифи

БУДСТАНДАРТ Online