ДСТУ EN 15382:2017 Геосинтетичні бар`єри. Характеристики, потрібні для використання в транспортній інфраструктурі (EN 15382:2013, IDT)

Даний документ доступний у тарифі «ВСЕ ВРАХОВАНО»

У Вас є питання стосовно документа? Ми раді на них відповісти!Перелік безкоштовних документівПомітили помилку в документі або на сайті? Будь ласка, напишіть нам про це!Залишити заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(З питань придбання офіційного видання звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ»))

Наказ від 07.08.2017 № 210

EN 15382:2013

Geosynthetic barriers — Characteristics required
for use in transportation infrastructure

прийнято як національний стандарт
методом «підтвердження» за позначенням
Відповідає офіційному тексту

ДСТУ EN 15382:2017
(EN 15382:2013, IDT)

Геосинтетичні бар’єри. Характеристики, потрібні
для використання в транспортній інфраструктурі

З наданням чинності від 2017-10-01

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms, definitions and abbreviations

3.1 Terms and definitions

3.2 Abbreviations

4 Required characteristics and corresponding methods of test

4.1 General

4.2 Types of applications

4.3 Relevant characteristics

4.4 Characteristics relevant to specific conditions of use

4.4.1 General

4.4.2 Tear strength

4.4.3 Friction characteristics (direct shear and inclined plane tests)

4.4.4 Chemical resistance

4.4.5 Low temperature behaviour

4.4.6 Weathering

4.4.7 Resistance to wetting and drying

4.4.8 Freeze-thaw cycle resistance

4.4.9 Resistance to root penetration

4.5 Release of dangerous substances

5 Evaluation of conformity

5.1 General

5.2 Verification of values

5.3 Initial type tests

5.4 Factory production control

5.5 Inspection

6 Marking

Annex A (normative) Factory production control — Factory production control scheme

A.1 General

A.2 Product design

A.3 Production

A.3.1 Raw or incoming materials

A.3.2 Production process

A.4 Finished products

A.4.1 Raw or incoming materials

A.4.2 Alternative tests

A.4.3 Equipment

A.5 Provisions applicable to A.2, A.3 and A.4 (to be used where appropriate)

A.5.1 Records

A.5.2 Assessment of results

A.5.3 Traceability

A.5.4 Corrective action for non-conforming materials and products

A.5.5 Personnel

A.5.6 Quality management

Annex B (normative) Durability of geosynthetic barriers

B.1 Introduction

B.1.1 Standards to which this annex is common

B.1.2 Mechanisms of degradation

B.1.3 Service life

B.1.4 Use of rework materials

B.2 Test requirements

B.2.1 General requirement

B.2.2 Requirements for repeat testing

B.2.3 Requirements for individual materials

B.3 Durability tests

B.3.1 Introduction

B.3.2 Weathering

B.3.3 Resistance to micro-organisms

B.3.4 Resistance to environmental stress cracking

B.3.5 Resistance to leaching

B.3.6 Resistance to oxidation

B.3.7 Chemical resistance

B.4 Evaluation tests and acceptance criteria

B.4.1 General

B.4.2 Evaluation by comparison of tensile properties

B.4.3 Evaluation by comparison of Oxidative Induction Time (OIT) values

B.4.4 Evaluation by change in mass

B.4.5 Evaluation by change in water permeability

Annex C (informative) Major technical changes to previous edition

Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive

ZA.1 Scope and relevant characteristics

ZA.2 Procedure for the attestation of conformity for geosynthetic barriers used in transportation infrastructure

ZA.2.1 Systems of attestation of conformity

ZA.2.2 Certificate and declaration of conformity

ZA.3 CE marking and labelling

Bibliography

Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».

Увійти в Особистий кабінет Детальніше про тарифи

БУДСТАНДАРТ Online