ДСТУ EN 13384-2:2018 Конструкції для видалення димових газів. Теплотехнічний та аеродинамічний розрахунок. Частина 2. Конструкції для видалення димових газів від кількох джерел тепла (EN 13384-2:2015, IDT)

Даний документ доступний у тарифі «ВСЕ ВРАХОВАНО»

У Вас є питання стосовно документа? Ми раді на них відповісти!Перелік безкоштовних документівПомітили помилку в документі або на сайті? Будь ласка, напишіть нам про це!Залишити заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(З питань придбання офіційного видання звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ»))

Наказ від 17.12.2018 № 498

EN 13384-2:2015

Chimneys — Thermal and fluid dynamic calculation methods —
Part 2: Chimneys serving more than one heating appliance

прийнято як національний стандарт
 методом «підтвердження» за позначенням
Відповідає офіційному тексту

ДСТУ EN 13384-2:2018
(EN 13384-2:2015, IDT)

 Конструкції для видалення димових газів. Теплотехнічний та аеродинамічний розрахунок.
Частина 2. Конструкції для видалення димових газів від кількох джерел тепла

З наданням чинності від 2019–01–01

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 General symbols and abbreviations

5 Calculation method

5.1 General principles

5.2 Pressure equilibrium condition

5.3 Mass flow requirement

5.4 Pressure requirements

5.5 Temperature requirement

5.6 Calculation procedure

6 Flue gas data characterising the heating appliance

7 Data for chimney and connecting flue pipes

8 Basic data for the calculation

8.1 General

8.2 Air temperatures

8.3 External air pressure (pL)

8.4 Gas constant

8.5 Density of air (ρL)

8.6 Specific heat capacity of the flue gas (cp)

8.7 Water vapour content (σ(H2O),j) and condensing temperature (Tsp)

8.8 Correction factor for temperature instability (SH)

8.9 Flow safety coefficient (SE)

8.10 External coefficient of heat transfer

9 Determination of temperatures

10 Mixing calculations

10.1 General

10.2 Flue gas mass flow (m,j)

10.3 Flue gas temperature at the inlet of the chimney segment (Te,j)

10.4 CO 2 -content of the flue gas in the chimney segment (σ(CO2),j)

10.5 H 2 O-content of the flue gas (σ(H2O),j)

10.6 Gas constant of the flue gas (R,j)

10.7 Flue gas data

11 Density and velocity of the flue gas

12 Determination of the pressures

12.1 Pressures at each inlet of the chimney segments

12.2 Minimum draught required at the flue gas inlet into the chimney and maximum allowed draught (PZe and PZemax) and maximum and minimum differential pressure at the flue gas inlet into the chimney (PZOe and PZOemin)

13 Inner wall temperature

14 Cascade installations

14.1 Principle of the calculation method

14.2 Pressure equilibrium condition

14.3 Mass flow requirement

14.4 Pressure requirements

14.5 Temperature requirement

14.6 Calculation procedure

14.7 Pressures at the outlet of the connecting flue pipe and pressures at the inlet of the collector segment

14.8 Inner wall temperature (TiobC,j,I)

15 Balanced flue chimney

15.1 Principle of the calculation method

15.2 Pressure equilibrium condition

15.3 Mass flow requirement

15.4 Pressure requirements

15.5 Temperature requirements

15.6 Calculation procedure for balanced flue chimneys

15.7 Mass flow of the supply air

15.8 Determination of the temperatures in balanced flue chimneys

15.9 Pressures of the air supply ducts

15.10 Density and velocity of the supply air

16 Consideration of chimney fans

16.1 General

16.2 Inline fans

16.3 Exhaust fans

Annex A (informative) Recommendations

Annex B (informative) Characteristics for the heating appliance

Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».

Увійти в Особистий кабінет Детальніше про тарифи

БУДСТАНДАРТ Online