ДСТУ EN 15502-2-1:2019 Котли газові для центрального опалення. Частина 2-1. Спеціальний стандарт для приладів типу C та приладів типів B2, B3 та B5 з номінальною тепловою потужністю не більше ніж 1000 кВт (EN...

Даний документ доступний у тарифі «ВСЕ ВРАХОВАНО»

У Вас є питання стосовно документа? Ми раді на них відповісти!Перелік безкоштовних документівПомітили помилку в документі або на сайті? Будь ласка, напишіть нам про це!Залишити заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(З питань придбання офіційного видання звертайтесь до національного органу стандартизації
(ДП «УкрНДНЦ»))

Наказ від 12.12.2019 № 410

EN 15502-2-1:2012

Gas-fired central heating boilers —
Part 2-1: Specific standard for type C appliances and type B2, B3
and B5 appliances of a nominal heat input not exceeding 1 000 kW

прийнято як національний стандарт
методом «підтвердження» за позначенням
Відповідає офіційному тексту

ДСТУ EN 15502-2-1:2019
(EN 15502-2-1:2012, IDT)

Котли газові для центрального опалення.
Частина 2-1. Спеціальний стандарт для приладів типу C
та приладів типів B2, B3 та B5 з номінальною
тепловою потужністю не більше ніж 1 000 кВт

З наданням чинності від 2020–01–01

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms, definitions and symbols

3.1 Terms and definitions

3.2 Symbols

4 Classification

5 Construction

5.1 General

5.2 Conversion to different gases

5.3 Materials

5.4 Method of construction

5.5 Burners

5.6 Pressure test points

5.7 Requirements for the application of control and safety devices

5.101 Additional requirements for modular boilers

6 Electrical safety

7 Controls

8 Operational requirements

8.1 General

8.2 Soundness

8.3 Hydraulic resistance

8.4 Heat inputs and heat output

8.5 Limiting temperatures

8.6 Ignition, cross lighting, flame stability

8.7 Reduction of the gas pressure

8.8 Defective closure of the gas valve immediately upstream of the main burner

8.9 Pre-purge

8.10 Functioning of a permanent ignition burner when the fan stops during the standby time

8.11 Adjustment, control and safety devices

8.12 Carbon monoxide

8.13 NOx

8.14 Special provisions for boilers intended to be installed in a partially protected place

8.15 Formation of condensate

8.16 Temperature of combustion products

8.101 Mechanical resistance and stability of ducts, terminal and fitting pieces

8.102 Requirements for plastic in the combustion product evacuation ducts, terminals and fitting pieces for boilers

8.103 Requirements for elastomeric seals and elastomeric sealants in the combustion product evacuation ducts, terminals and fitting pieces

9 Useful efficiencies

10 Electric auxiliary energy

11 Risk assessment

12 Marking and instructions

12.1 Boiler marking

12.2 Instructions

12.3 Presentation

12.4 Supplementary marking and instructions in the case of boilers to be installed in partially protected places

101 Figures

102 Listing of tables and numbers

103 Annexes

Annex AA (informative) Standards replaced by this standard in combination with part 1

Annex BB (normative) Test apparatus for type C2 boilers

Annex CC (normative) Test methods to determine the effects of long-term thermal load, long-term condensate exposure, condensing/non-condensing cycling and resistance to UV radiation

Annex DD (informative) Variations in gas quality

Annex ZA (informative) Clauses of this European Standard addressing essential requirements or provisions of EU Directive 2009/142/EC, "Directive relating to appliances burning gaseous fuels (codified version)" (GAD)

 Annex ZB (informative) Clauses of this European Standard addressing the methods for the verification of the efficiency of the EU Directive 92/42/EEC, relating to the efficiency of new hot boilers with an output of 4 – 400 kW

Bibliography

Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».

Увійти в Особистий кабінет Детальніше про тарифи

БУДСТАНДАРТ Online