ДСТУ EN 13964:2019 Стелі підвісні. Вимоги та методи випробування (EN 13964:2014, IDT)

Даний документ доступний у тарифі «ВСЕ ВРАХОВАНО»

У Вас є питання стосовно документа? Ми раді на них відповісти!Перелік безкоштовних документівПомітили помилку в документі або на сайті? Будь ласка, напишіть нам про це!Залишити заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)

Наказ від 23.12.2019 № 477

EN 13964:2014

Suspended ceilings - Requirements and test methods

прийнято як національний стандарт
методом підтвердження за позначенн¤м

ДСТУ EN 13964:2019
(EN 13964:2014, IDT)

Стелі підвісні. Вимоги та методи випробування

З наданням чинності від 2020–01–01

Відповідає офіційному тексту

З питань придбання офіційного видання звертайтесь
до національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.org.ua)

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

3.1 General

3.2 Suspended ceiling and substructure components (see Figure 1)

3.3 Ceiling membranes and ceiling membrane components

3.4 Typical suspended ceiling systems using volume or thin gauge materials

4 Requirements

4.1 Dimensions and tolerances - General

4.2 Modular dimensions

4.3 Mechanical resistance and stability of load bearing components

4.4 Safety in case of fire

4.5 Hygiene, health and environment - Toxic gases and dangerous substances

4.6 Safety in use

4.7 Acoustics

4.8 Durability

4.9 Colour, light reflectance and gloss factor for suspended ceiling components

4.10 Thermal insulation

5 Loading capacity of substructures components - Test methods

5.1 General

5.2 Bending test of metal substructure profiles

5.3 Testing of metal suspension and connecting components

5.4 Acceptance factor kσ

6 Evaluation of conformity

6.1 General

6.2 Initial type testing

6.3 Factory production control (FPC)

7 Marking, labelling and packaging

7.1 Marking and labelling

7.2 Packaging

8 Technical documentation

Annex A (informative) Guidance for installation

Annex B (informative) Selection of top fixing and perimeter trim fixing

Annex C (informative) Wind load resistance

Annex D (normative) Impact resistance

Annex E (normative) Formaldehyde classes and associated test methods

Annex F (normative) Membrane components - Flexural tensile strength test

Annex G (normative) Suspension component - Functional test

Annex H (normative) Perimeter trim component - Functional test, determination of load bearing capacity

Annex I (normative) Reaction to fire test - Mounting and fixing

Annex J (normative) Mechanical strength, safety against failure - baffles

Annex K (informative) Reaction to fire performance - Classified without the need for further testing (CWFT)

Annex L (informative) Guidance on the choice of attestation of conformity system

Annex M (informative) Significant technical changes between this European Standard and the previous edition

Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives

Bibliography

Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».

Увійти в Особистий кабінет Детальніше про тарифи

БУДСТАНДАРТ Online