ДСТУ EN 60204-11:2014 Електрообладнання промислових машин. Безпека. Частина 11. Вимоги до високовольтного обладнання, працюючого при напругах понад 1000 В змінного струму або 1500 В постійного струму і не вищ...

Даний документ доступний у тарифі «ВСЕ ВРАХОВАНО»

У Вас є питання стосовно документа? Ми раді на них відповісти!Перелік безкоштовних документівПомітили помилку в документі або на сайті? Будь ласка, напишіть нам про це!Залишити заявку на документ

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

МІНІСТЕРСТВО ЕКОНОМІЧНОГО РОЗВИТКУ І ТОРГІВЛІ УКРАЇНИ

Наказ від 29.12.2014 № 1479

EN 60204-11:2000, EN 60204-11:2000/AC:2010

en: Safety of machinery - Electrical equipment of machines - Part 11: Requirements
for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not
exceeding 36 kV

прийнято як національний стандарт
методом підтвердження за позначенням

ДСТУ EN 60204-11:2014

uk: Електрообладнання промислових машин. Безпека. Частина 11. Вимоги до
високовольтного обладнання, працюючого при напругах понад 1000 В змінного
струму або 1500 В постійного струму і не вище 36 кВ
(EN 60204-11:2000, EN 60204-11:2000/AC:2010, IDT)

З наданням чинності від 2016-01-01

Відповідає офіційному тексту

З питань придбання офіційного видання звертайтесь
до національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.org.ua)

CONTENTS

INTRODUCTION

1 Scope

2 Normative references

3 Definitions

4 General requirements

4.1 General considerations

4.2 Selection of electrical equipment

4.3 Electrical supply

4.4 Physical environment and operating conditions

4.5 Transportation and storage

4.6 Provisions for handling

4.7 Installation

5 Incoming supply conductor terminations, devices for disconnecting and switching off, and means for earthing

5.1 Incoming supply conductor terminations

5.2 Supply disconnecting (isolating) devices and means for earthing

5.3 Devices for switching off for prevention of unexpected start-up

5.4 Devices for disconnecting and means for earthing HV equipment

5.5 Protection against unauthorized, inadvertent and/or mistaken operation

6 Protection against electric shock

6.1 General

6.2 Protection against direct contact

6.3 Protection against indirect contact

7 Protection of HV equipment

7.1 General

7.2 Overcurrent protection

7.3 Earth fault protection

7.4 Protection against overvoltages due to lightning and to switching surges

7.5 Protection against other abnormal conditions

8 Equipotential bonding

8.1 General

8.2 Protective bonding circuit

9 Control circuits and control functions

10 Operator interface and machine-mounted control devices

11 Electronic equipment

12 Controlgear: location, mounting, and enclosures

12.1 General requirements

12.2 Location and mounting

12.3 Degrees of protection

12.4 Enclosures, doors and openings

12.5 Access to HV equipment

13 Conductors and cables

13.1 General requirements

13.2 Conductors

13.3 Insulation and sheath materials

13.4 Current-carrying capacity in normal service

13.5 Conductor and cable voltage drop

13.6 Minimum cross-sectional area

13.7 Flexible cables

13.8 Conductor wires, conductor bars and slip-ring assemblies

14 Wiring practices

14.1 Connections and routing

14.2 Identification of conductors

14.3 Flexible cables

14.4 Plug/socket combinations

14.5 Dismantling for shipment

14.6 Cabletrays

15 Electric motors and associated equipment

15.1 General

15.2 Motor connection boxes

16 Accessories

16.1 Accessories for earthing and short-circuiting live parts

16.2 Voltage detectors

16.3 Accessories for safe working

17 Marking, warning signs and reference designations

17.1 General

17.2 Warning signs

18 Technical documentation

19 Testing and verification

19.1 General

19.2 Earthing system tests

19.3 Insulation resistance tests

19.4 Voltage tests

19.5 Functional tests

19.6 IP tests for HV equipment outside electrical operating areas

19.7 Retesting

Annex A (informative) Examples of machines covered by this part of IEC 60204

Annex В (informative) Inquiry form for the HV equipment of machines

Annex C (informative) Method of calculation for the cross-sectional area of bare protective conductors in supply systems with direct earthing or low impedance earthing of the neutral

Annex D (informative) Relationship between cable rated voltages and highest voltage for HV equipment

Annex E (informative) Rationalization of the use of terms relating to earthing and protective bonding

Annex ZA (normative) Normative references to international publications with their corresponding European publications

Annex ZZ (informative) Coverage of Essential Requirements of EC Directives

Index

Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».

Увійти в Особистий кабінет Детальніше про тарифи

БУДСТАНДАРТ Online