ДСТУ EN IEC 61851-1:2021 Система зарядки електричних транспортних засобів дротова. Частина 1. Загальні вимоги (EN IEC 61851-1:2019, IDT; IEC 61851-1:2017, IDT)
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)
Наказ від 13.09.2021 № 319
EN IEC 61851-1:2019
Electric vehicle conductive charging system - Part 1: General requirements
прийнято як національний стандарт
методом «підтвердження» за позначенням
ДСТУ EN IEC 61851-1:2021
(EN IEC 61851-1:2019, IDT; IEC 61851-1:2017, IDT)
Система зарядки електричних транспортних засобів дротова.
Частина 1. Загальні вимоги
З наданням чинності від 2021-09-15
Відповідає офіційному тексту
З питань придбання офіційного видання звертайтесь
до національного органу стандартизації
(ДП «УкрНДНЦ» http://uas.org.ua)
CONTENTS
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
3.1 Electric supply equipment
3.2 Insulation
3.3 Functions
3.4 Vehicle
3.5 Cords, cables and connection means
3.6 Service and usage
3.7 General terms
4 General requirements
5 Classification
5.1 Characteristics of power supply and output
5.2 Normal environmental conditions
5.3 Special environmental conditions
5.4 Access
5.5 Mounting method
5.6 Protection against electric shock
5.7 Charging modes
6 Charging modes and functions
6.1 General
6.2 Charging modes
6.3 Functions provided in Mode 2, 3 and 4
7 Communications
7.1 Digital communication between the EV supply equipment and the EV
7.2 Digital communication between the EV supply equipment and the management system
8 Protection against electric shock
8.1 Degrees of protection against access to hazardous-live-parts
8.2 Stored energy
8.3 Fault protection
8.4 Protective conductor
8.5 Residual current protective devices
8.6 Safety requirements for signalling circuits between the EV supply equipment and the EV
8.7 Isolating transformers
9 Conductive electrical interface requirements
9.1 General
9.2 Functional description of standard accessories
9.3 Functional description of the basic interface
9.4 Functional description of the universal interface
9.5 Functional description of the DC interface
9.6 Functional description of the combined interface
9.7 Wiring of the neutral conductor
10 Requirements for adaptors
11 Cable assembly requirements
11.1 General
11.2 Electrical rating
11.3 Dielectric withstand characteristics
11.4 Construction requirements
11.5 Cable dimensions
11.6 Strain relief
11.7 Cable management and storage means for cables assemblies
12 EV supply equipment constructional requirements and tests
12.1 General
12.2 Characteristics of mechanical switching devices
12.3 Clearances and creepage distances
12.4 IP degrees
12.5 Insulation resistance
12.6 Touch current
12.7 Dielectric withstand voltage
12 8 Temperature rise
12.9 Damp heat functional test
12.10 Minimum temperature functional test
12.11 Mechanical strength
13 Overload and short-circuit protection
13.1 General
13.2 Overload protection of the cable assembly
13.3 Short-circuit protection of the charging cable
14 Automatic reclosing of protective devices
15 Emergency switching or disconnect (optional)
16 Marking and instructions
16.1 Installation manual of EV charging stations
16.2 User manual for EV supply equipment
16.3 Marking of EV supply equipment
16.4 Marking of charging cable assemblies case В
16.5 Durability test for marking
Annex A (normative) Control pilot function through a control pilot circuit using a PWM signal and a control pilot wire
Annex В (normative) Proximity detection and cable current coding circuits for the basic interface
Annex C (informative) Examples of circuit diagrams for a basic and universal vehicle couplers
Annex D (informative) Control pilot function that provides LIN communication using the control pilot circuit
Annex E (informative) Charging station designed with a standard socket-outlet - Minimum gap for connection of Modes 1 and 2 cable assembly
Bibliography
Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».