ДСТУ IEN 60839-11-1:2014 Системы тревожной сигнализации и электронные системы безопасности. Часть 11-1. Электронные системы контроля доступа. Требования к системе и ее составляющих (EN 60839-11-1:2013, EN 608...

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Наказом Міністерства економічного розвитку і торгівлі України

від 30.12.2014 № 1494

EN 60839-11-1:2013

en: Alarm and electronic security systems - Part 11-1: Electronic access control systems - System and components requirements

прийнято як національний стандарт
методом «підтвердження» за позначенням
 

ДСТУ EN 60839-11-1:2014

uk: Системи тривожної сигналізації та електронні системи безпеки.
Частина 11-1. Електронні системи контролювання доступу. Вимоги до системи та її складників

(EN 60839-11-1:2013; EN 60839-11-1:2013/АС:2013, IDТ)

З наданням чинності від 2016-01-01

CONTENTS

FOREWORD

INTRODUCTION

1 Scope

2 Normative references

3 Terms and definitions

4 Abbreviations

5 Conceptual models and system architecture

6 System performance functionality requirements

6.1 Classification methodology and functionalities - Determining the levels of protection

6.2 Access point interface requirements

6.2.1 Portal release timing

6.2.2 Access control

6.2.3 Portal status

6.3 Indication and annunciation (display, alert, logging) requirements

6.3.1 Annunciation

6.3.2 Display

6.3.3 Alert

6.3.4 Logging

6.4 Recognition requirements

6.5 Duress signalling requirements

6.6 Overriding requirements

6.7 Communication requirements

6.8 System self-protection requirements

6.9 Power supply requirements

7 Environmental and EMC (immunity) requirements

8 Test methods

8.1 General conditions

8.1.1 Atmospheric conditions for tests

8.1.2 Operating conditions for tests

8.1.3 Specimen configuration

8.1.4 Mounting arrangements

8.1.5 Tolerances

8.1.6 Provisions for tests

8.1.7 Optional functions

8.2 Reduced functional tes

8.3 Functional tests for access point interface

8.3.1 Object of the test

8.3.2 Principle

8.3.3 Procedure

8.3.4 Criteria for compliance

8.4 Functional tests for indication/annunciation (displaying, alert and logging)

8.4.1 Object of the test

8.4.2 Principles

8.4.3 Test procedure

8.4.4 Criteria for compliance

8.5 Test methods for recognition functionalities

8.5.1 Object of the test

8.5.2 Principles

8.5.3 Test procedure

8.5.4 Criteria for compliance

8.6 Functional tests for duress signalling

8.6.1 Object of the test

8.6.2 Principles

8.6.3 Test procedure (ref. Table 5, lines 1 to 3)

8.6.4 Criteria for compliance

8.7 Functional tests for overriding

8.7.1 Object of the test

8.7.2 Principles

8.7.3 Test procedure (ref. Table 6, lines 1 to 7)

8.7.4 Criteria for compliance

8.8 Functional tests for communication and self-protection

8.8.1 Object of the test

8.8.2 Principles

8.8.3 Test procedure (ref. Table 7, lines 1 to 28)

8.8.4 Criteria for compliance

8.9 Power supply requirements

8.9.1 Test of standby power duration

8.9.2 Test of charger and standby power source capacity

8.9.3 Test for low or missing battery condition

8.10 Environmental and EMC (immunity) tests

8.10.1 Test procedure

8.10.2 Initial measurements

8.10.3 State of the specimen during conditioning

8.10.4 Conditioning

8.10.5 Measurement during conditioning

8.10.6 Final measurements

8.10.7 Criteria for compliance

8.11 Test report

9 Documentation and marking

9.1 Documentation

9.2 Marking

Annex A (normative) Timing diagram

Bibliography

Figure 1 - Conceptual model

Figure 2 - Typical architecture of an electronic access control system

Figure 3 - Example of system test configuration

Figure A.1 - Timing diagram

Table 1 - Grade classification

Table 2 - Access point interface requirements

Table 3 - Indication and annunciation requirements

Table 4 - Recognition requirements

Table 5 - Duress signalling requirements

Table 6 - Overriding requirements

Table 7 - System self-protection requirements

Table 8 - Power supply requirements

Table 9 - Environmental and EMC (immunity) requirements