ДСТУ IEC 62599-2:2017 Системы тревожной сигнализации. Часть 2. Электромагнитная совместимость. Требования к невосприимчивости составляющих систем пожарной и охранной сигнализации (IEC 62599-2:2010, IDT)

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(   
(ДП «УкрНДНЦ»))

Наказ від 13.12.2017 №413

ІЕС 62599-2:2010

Alarm systems —
Part 2: Electromagnetic compatibility —
Immunity requirements for components
of fire and security alarm systems

прийнято як національний стандарт
методом «підтвердження» за позначенням
 

ДСТУ ІЕС 62599-2:2017
(ІЕС 62599-2:2010, IDТ)

Системи тривожної сигналізації.
Частина 2. Електромагнітна сумісність.
Вимоги до несприйнятливості складників
систем пожежної та охоронної сигналізації

З наданням чинності від 2017-12-15

CONTENTS

FOREWORD

1 Scope

2 Normative references

3 Terms, definitions and abbreviations

3.1 Terms and definitions

3.2 Abbreviations

4 Application of tests

5 Conditions during testing

5.1 Configuration

5.2 Environmental conditions

5.3 Operating condition

6 Functional test

7 Mains supply voltage variations

7.1 Object of the test

7.2 Principle

7.3 Test procedure

7.3.1 General

7.3.2 Initial examination

7.3.3 State of specimen during conditioning

7.3.4 Conditioning

7.3.5 Measurements during conditioning

7.3.6 Final measurements

7.4 Criteria for compliance

8 Mains supply voltage dips and short interruptions

8.1 Object of the test

8.2 Principle

8.3 Test procedure

8.3.1 General

8.3.2 Initial examination

8.3.3 State of specimen during conditioning

8.3.4 Conditioning

8.3.5 Measurements during conditioning

8.3.6 Final measurements

8.4 Criteria for compliance

9 Electrostatic discharge

9.1 Object of the test

9.2 Principle

9.3 Test procedure

9.3.1 General

9.3.2 Initial examination

9.3.3 State of specimen during conditioning

9.3.4 Conditioning

9.3.5 Measurements during conditioning

9.3.6 Final measurements

9.4 Criteria for compliance

10 Radiated electromagnetic fields

10.1 Object of the test

10.2 Principle

10.3 Test procedure

10.3.1 General

10.3.2 Initial examination

10.3.3 State of specimen during conditioning

10.3.4 Conditioning

10.3.5 Measurements during conditioning

10.3.6 Final measurements

10.4 Criteria for compliance

11 Conducted disturbances induced by electromagnetic fields

11.1 Object of the test

11.2 Principle

11.3 Test procedure

11.3.1 General

11.3.2 Initial examination

11.3.3 State of specimen during conditioning

11.3.4 Conditioning

11.3.5 Measurements during conditioning

11.3.6 Final measurements

11.4 Criteria for compliance

12 Fast transient bursts

12.1 Object of the test

12.2 Principle

12.3 Test procedure

12.3.1 General

12.3.2 Initial examination

12.3.3 State of specimen during conditioning

12.3.4 Conditioning

12.3.5 Measurements during conditioning

12.3.6 Final measurements

12.4 Criteria for compliance

13 Slow high energy voltage surge

13.1 Object of the test

13.2 Principle

13.3 Test procedure

13.3.1 General

13.3.2 Initial examination

13.3.3 State of specimen during conditioning

13.3.4 Conditioning

13.3.5 Measurements during conditioning

13.3.6 Final measurements

13.4 Criteria for compliance

Figure 1 - Example of relative orientations of the EUT and the field vectors

Figure 2 - Forms of the modulation types relative to the continuous wave

Figure 3 - Typical arrangement for coupling onto screened signal lines

Table 1

Table 2

Table 3

Table 4

Table 5

Table 6

Table 7