ДСТУ EN IEC/IEEE 62209-1528:2022 Процедура вимірювання для оцінювання питомого рівня поглинання радіочастотних полів на людину від ручних і натільних пристроїв бездротового зв’язку. Частина 1528. Моделі людин...

ДСТУ EN IEC/IEEE 62209-1528:2022
(EN IEC/IEEE 62209-1528:2021, IDT; IEC/IEEE 62209-1528:2020, IDT)

Процедура вимірювання для оцінювання питомого рівня поглинання
радіочастотних полів на людину від ручних і натільних пристроїв
бездротового зв’язку. Частина 1528. Моделі людини, прилади та
процедури (діапазон частот від 4 МГц до 10 ГГц)

 
   
 
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 Symbols and abbreviated terms

4.1 Physical quantities

4.2 Constants

4.3 Abbreviated terms

5 Quick start guide and evaluation plan checklist

6 Measurement system specifications

6.1 General requirements for full SAR testing

6.2 Phantom specifications

6.3 Influence of hand on SAR in head

6.4 Scanning system requirements

6.5 Device holder specifications

6.6 Characteristics of the readout electronics

7 Protocol for SAR assessment

7.1 General

7.2 Measurement preparation

7.3 Tests to be performed for DUTs

7.4 Measurement procedure

7.5 Post-processing of SAR measurement data

7.6 Time-period averaged SAR considerations

7.7 Proximity sensors considerations

7.8 SAR correction for deviations of complex permittivity from targets

7.9 Minimization of testing time

8 Measurement uncertainty estimation

8.1 General

8.2 Requirements on the uncertainty evaluation

8.3 Description of uncertainty models

8.4 Parameters contributing to uncertainty

9 Measurement report

9.1 General

9.2 Items to be recorded in the measurement report

Annex A (normative) SAR measurement system verification

Annex В (informative) SAR test reduction supporting information

Annex C (informative) Measurement uncertainty of results obtained from specific fast SAR testing methods

Annex D (normative) SAR system validation antennas

Annex E (normative) Calibration and characterization of dosimetric (SAR) probes

Annex F (informative) Example recipes for phantom tissue-equivalent media

Annex G (normative) Phantom specifications

Annex H (informative) Measurement of the dielectric properties of tissue-equivalent media and uncertainty estimation

Annex I (informative) Studies for potential hand effects on head SAR

Annex J (informative) Skin enhancement factor

Annex К (normative) Application-specific phantoms

Annex L (normative) Fast compliance evaluations using a flat-bottom phantom with a curved corner (Uniphantom)

Annex M (informative) Wired hands-free headset testing

Annex N (informative) Applying the head SAR test procedures

Annex О (normative) Uncertainty analysis for measurement system manufacturers and calibration laboratories

Annex P (normative) Post-processing techniques

Annex Q (informative) Rationale for time-period averaged SAR test procedure

Annex R (normative) Measurement uncertainty analysis for testing laboratories

Annex S (normative) Validation antenna SAR measurement uncertainty

Annex T (normative) Interlaboratory comparisons

Annex U (informative) Determination of the margin for compliance evaluation using the Uniphantom

Annex V (informative) Automatic input power level control for system validation

Annex W (informative) LTE test configurations supporting information

Bibliography