ДСТУ EN ISO 10407-2:2022 Нафтова та газова промисловість. Ротаційне бурове обладнання. Частина 2. Перевірка та класифікація використаних елементів бурової штанги (EN ISO 10407-2:2008, IDT; ISO 10407-2:2008, I...

ДСТУ EN ISO 10407-2:2022
(EN ISO 10407-2:2008, IDT; ISO 10407-2:2008, IDT)

 Нафтова та газова промисловість. Ротаційне бурове
обладнання. Частина 2. Перевірка та класифікація
використаних елементів бурової штанги

 
   
 
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 Symbols and abbreviated terms

4.1 Symbols

4.2 Abbreviated terms

5 Conformance

5.1 Basis for inspection

5.2 Repeatability of results

5.3 Ordering information

6 Quality assurance

6.1 General

6.2 Standardization and operating procedures

6.3 Equipment description

6.4 Personnel qualification

6.5 Dynamic test data demonstrating the system capabilities for detecting the reference indicators

6.6 Reports

7 Qualification of inspection personnel

7.1 General

7.2 Written procedure

7.3 Qualification responsibility and requirements

7.4 Training programmes

7.5 Examinations

7.6 Experience

7.7 Re-qualification

7.8 Documentation

7.9 NDT personnel certification

8 General inspection procedures

8.1 General

8.2 Owner/operator work site requirements for quality inspection

8.3 Documents at job site

8.4 Pre-inspection procedures

8.5 Drill-pipe and tool-joint classification markings

8.6 Post-inspection procedures

9 General non-destructive inspection method requirements

9.1 General

9.2 Equipment

9.3 Illumination

9.4 Magnetic-particle-inspection equipment

9.5 Ultrasonic

9.6 Electromagnetic inspection units

10 Drill stem element inspection and classification

10.1 Pipe body - Full-length visual inspection

10.2 Drill body - Outside diameter gauging

10.3 Pipe body - Ultrasonic wall-thickness gauging

10.4 Pipe body - Full-length electromagnetic inspection (EMI)

10.5 Pipe body - Full-length ultrasonic transverse and wall thickness

10.6 Pipe body - Full-length ultrasonic transverse, wall thickness and longitudinal inspection

10.7 Drill-pipe body - External magnetic-particle inspection of the critical area

10.8 Drill-pipe body - Bi-directional external magnetic-particle inspection of the critical area

10.9 Pipe body - Full-length wall-loss inspection

10.10 Pipe body - Ultrasonic inspection of the critical area

10.11 Pipe body - Calculation of cross-sectional area

10.12 Pipe body - Document review (traceability)

10.13 Pipe body - Evaluation and classification

10.14 Tool joints

10.15 Tool joints - Check for box swell and pin stretch

10.16 Repair of rejected tool joints

10.17 Tool joints - Check tool-joint pin and box outside diameter and eccentric wear

10.18 Tool joints - Measure tool-joint pin and box outside diameter and check for eccentric wear

10.19 Tool joints - Check tool-joint pin and box tong space

10.20 Tool joints - Measure tool-joint pin and box tong space

10.21 Tool joint - Magnetic-particle inspection of the pin threads

10.22 Tool joint - Magnetic-particle inspection of box threads

10.23 Tool joints - Measure tool-joint pin inside diameter

10.24 Magnetic-particle inspection of the connection OD for heat-check cracking

10.25 Bi-directional wet magnetic-particle inspection of the connection OD for heat-check cracking

10.26 Tool joints - Measure the tool-joint counterbore depth, pin-base length and seal width

10.27 BHA connection - Visual inspection of bevels, seals, threads and stress-relief features

10.28 BHA - Measure box outside diameter, pin inside diameter, counterbore diameter and benchmark location if a benchmark is present

10.29 BHA - Check bevel diameter

10.30 BHA - Measure bevel diameter

10.31 BHA - Magnetic-particle inspection of the pin and box threads

10.32 BHA connection - Liquid-penetrant inspection of the pin and box threads

10.33 BHA - Dimensional measurement of stress-relief features

10.34 Length measurements of the counterbore, pin and pin neck

10.35 Drill collar - Visual full-length OD and ID, markings, fish-neck length and tong space

10.36 Drill-collar elevator groove and slip-recess magnetic-particle inspection

10.37 Drill-collar elevator-groove and slip-recess measurement

10.38 Subs (full-length visual OD and ID), fish-neck length, section-change radius and markings

10.39 Float-bore recess measurements

10.40 Magnetic-particle inspection of subs - Full-length, internal and external

10.41 HWDP - Visual full-length OD and ID, markings and tong space

10.42 Visual inspection and wear pattern report for kelly

10.43 Magnetic-particle evaluation of critical areas on kellys

10.44 Magnetic-particle evaluation, full length, of the drive section on kellys

10.45 Stabilizer (full-length visual OD and ID), fish-neck length, blade condition, ring gauge and markings

10.46 Magnetic-particle inspection of the base of stabilizer blades for cracking

10.47 Function test

10.48 Bi-directional, wet magnetic-particle inspection of the base of stabilizer blade for cracking

10.49 Visual inspection of jars (drilling and fishing), accelerators and shock subs

10.50 Maintenance review

10.51 Dimensional measurement of wear areas as specified by OEM requirements

10.52 Original equipment manufacturer designated testing for used equipment

10.53 MWD/LWD - Visual, full-length OD and ID, and markings, including visual inspection of hard-banding and coatings

10.54 Motors and turbines - Visual, full-length OD and ID and markings, including visual inspection of hard-banding and coatings

10.55 Reamers, scrapers, and hole openers - Visual, full-length OD and ID and markings, including visual inspection of hard-banding and coatings

10.56 Rotary steerable - Visual, full-length OD and ID and markings, including visual inspection of hard-banding

10.57 Full-length drift

10.58 Proprietary equipment inspection

10.59 Hard-banding inspection

10.60 Transverse magnetic-particle inspection of tool-joint OD and ID under the pin threads

10.61 Drill-pipe body - Internal magnetic-particle inspection of the critical area

10.62 Drill-pipe body - Bi-directional, internal magnetic-particle inspection of the critical area

10.63 API external upset-thread connection inspection

Annex A (normative) Original equipment manufacturer (OEM) requirements

Annex В (normative) Required and additional inspections by product and class of service

Annex C (normative) SI units

Annex D (informative) USC units

Annex E (informative) Inspection-level guidelines

Annex F (informative) Proprietary drill stem connection inspection

Annex G (informative) Used work-string tubing proprietary-connection thread inspection

Bibliography