ДСТУ ISO/IEC 23837-2:2024 Інформаційна безпека. Вимоги до безпеки, методи тестування та оцінювання розподілу квантових ключів. Частина 2. Методи оцінювання та тестування (ISO/IEC 23837-2:2023, IDT)



ДСТУ ISO/IEC 23837-2:2024
(ISO/IEC 23837-2:2023, IDT)

Інформаційна безпека. Вимоги до безпеки, методи тестування та оцінювання
розподілу квантових ключів. Частина 2. Методи оцінювання та тестування

 

 
   
 
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 Abbreviated terms

5 Overview of the evaluation method for QKD modules

5.1 General

5.2 Scope of the evaluation method

5.3 Overview of evaluation activities for SFRs

5.4 Overview of evaluation activities for SARs

6 EAs for the evaluation of FTP_QKD

6.1 General

6.2 EA to test quantum state transmission and sifting procedures

6.4 EA to test parameter adjustment procedure(s)

7 EAs for evaluating quantum optical components in the transmitter module

7.1 General

7.2 EA to test the photon-number distribution of optical pulses

7.3 EA to test the mean photon number and stability of optical pulses

7.4 EA to test the independence of the intensities of optical pulses

7.5 EA to test the accuracy of state encoding

7.6 EA to test the indistinguishability of encoded states

7.7 EA to test the uniform distribution of the global phase of optical pulses

7.8 EA to test the degree of optical isolation of the TX module

7.9 EA to test the sensitivity of the injected light monitor in the TX module

7.10 EA to test the robustness of the TX module against laser injection

8 EAs for the evaluation of quantum optical components in the receiver module

8.1 General

8.2 EA to test the consistency of detection probability in the RX module

8.3 EA to test information leakage of back-flashes from the RX module

8.4 EA to test the degree of optical isolation of the RX module

8.5 EA to test the sensitivity of the injected light monitor in the RX module

8.6 EA to test the robustness of the RX module against bright light blinding

8.7 EA to test the appropriateness of dead time settings of SPDs

8.8 EA to test the temporal profile of the detection efficiency for SPDs

8.9 EA to test the robustness of the RX module against laser injection

8.10 EA to test the detection limits of homodyne detectors in the RX module

8.11 EA to test the appropriateness of double-click event handling

9 EAs for the evaluation of parameter adjustment procedure(s)

9.1 General

9.2 EA to test the inducibility of detection probability mismatch

9.3 EA to test the correctness of shot noise alignment

10 Supplementary activities for the evaluation of SFRs on conventional network components

10.1 General

10.2 Evaluation activities for FCS related SFRs overview

10.3 Evaluation activities for other SFRs overview

11 Supplementary activities for SARs

11.1 General

11.2 Supplementary activities for Class APE: Protection Profile evaluation

11.3 Supplementary activities for Class ASE: Security Target evaluation

11.4 Supplementary activities for Class ADV: Development

11.5 Supplementary activities for Class AGD: Guidance documents

11.6 Supplementary activities for Class ATE: Test

11.7 Supplementary activities for Class AVA: Vulnerability assessment

12 Conformance statement

12.1 General

12.2 Conformance statement specific to evaluation activities for SFRs

12.3 Conformance statement specific to EAs for SARs

Annex A (informative) Guidance on the calculation of attack potential for the evaluation of QKD modules

Annex В (informative) Rating examples for AVA attack potential computation

Annex C (informative) Thresholds collection

Annex D (informative) Correspondence between EAs and known attacks to quantum optical components and parameter adjustment procedure(s) of QKD modules

Bibliography