ДСТУ EN 62275:2015 Системи кабельних органайзерів. Кабельні хомути для електричних установок (EN 62275:2015, IDT)

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(   
(ДП «УкрНДНЦ»))

Наказ від 12.02.2016 № 34

EN 62275:2015

Cable management systems - Cable ties for electrical installations

прийнято як національний стандарт
методом «підтвердження» за позначенням
 

ДСТУ EN 62275:2015
(EN 62275:2015, IDT)

Системи кабельних органайзерів. Кабельні хомути для електричних установок

З наданням чинності від 2016–01–01

CONTENTS

1 Scope

2 Normative references

3 Terms and definitions

4 General requirements

5 General notes on tests

6 Classification

6.1 According to material

6.1.1 Metallic component

6.1.2 Non-metallic component

6.1.3 Composite component

6.2 According to loop tensile strength for cable ties and mechanical strength for fixing devices

6.2.1 Loop tensile strength for cable ties

6.2.2 Type 1 – Retains at least 50 % of declared loop tensile strength for cable ties and mechanical strength for fixing devices after test conditions

6.2.3 Type 2 – Retains 100 % declared loop tensile strength for cable ties and mechanical strength for fixing devices after test conditions

6.3 According to temperature

6.3.1 According to maximum operating temperature for application given in Table 4

6.3.2 According to minimum operating temperature for application given in Table 5

6.3.3 According to minimum temperature during installation as declared by the manufacturer

6.4 According to contribution to fire for non-metallic and composite cable ties only

6.4.1 Flame propagating

6.4.2 Non-flame propagating

6.5 According to environmental influences

6.5.1 According to resistance to ultraviolet light for non-metallic and composite components

6.5.2 According to resistance to corrosion for metallic and composite components

7 Marking and documentation

8 Construction

9 Mechanical properties

9.1 Requirements

9.2 Installation test

9.3 Minimum installation temperature test for cable ties

9.4 Minimum operating temperature test for cable ties

9.5 Loop tensile strength test for cable ties classified according to 6.2.2

9.5.1 As-received condition

9.5.2 After heat ageing

9.5.3 After temperature cycling

Bibliography

Figure 1 – Reference thickness for cable ties

Figure 2 – Typical arrangements for cable tie orientation on split mandrel for tensile test

Figure 3 – Test apparatus for cable tie impact test

Figure 4 – Typical arrangement for the vibration test

Figure 5 – Typical arrangement of test assembly for fixing device test

Figure 6 – Arrangement for the needle flame test

Figure 7 – Recommended sample repositioning for ultraviolet light and water exposure

Table 1 – Stabilisation time for samples

Table 2 – Test mandrel diameter

Table 3 – Loop tensile strength

Table 4 – Maximum operating temperature for application

Table 5 – Minimum operating temperature for application

Table 6 – Energy values of hammer

Table A.1 – Required compliance checks

9.6 Loop tensile strength test for cable ties classified according to 6.2.3

9.6.1 As-received condition

9.6.2 After heat ageing

9.6.3 After temperature cycling

9.6.4 After vibration test for metallic cable ties

9.7 Mechanical strength test for fixing devices

9.7.1 As-received

9.7.2 After heat ageing

9.7.3 After temperature cycling

10 Contribution to fire

11 Environmental influences

11.1 Resistance to ultraviolet light

11.2 Resistance to corrosion