ДСТУ EN 13121-3:2017 Устатковання ємкісне зі склопластиків (GRP) надземне. Частина 3. Проектування та якість виготовлення (EN 13121-3:2016, IDT)
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(
(ДП «УкрНДНЦ»))
Наказ від 26.12.2017 № 460
EN 13121-3:2016
GRP tanks and vessels for use above ground —
Part 3: Design and workmanship
прийнято як національний стандарт
методом «підтвердження» за позначенням
ДСТУ EN 13121-3:2017
(EN 13121-3:2016, IDT)
Устатковання ємкісне зі склопластиків (GRP) надземне.
Частина 3. Проектування та якість виготовлення
З наданням чинності від 2018–02–01
Contents
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Information and requirements to be supplied and documented
5.1 General
5.2 Information to be obtained by the manufacturer
5.3 Information to be prepared by the manufacturer
5.4 Final documentation
6 Material
6.1 General
6.2 Chemical protective barrier
6.3 Flammability
6.4 Electrical resistivity
7 Mechanical properties
7.1 General
7.2 Heat deflection temperature
7.3 Laminate construction
7.4 Laminate thickness
7.5 Laminate properties
7.6 Inter-laminar shear strength
7.7 Peel strength of laminates
7.8 Pull-off strength of laminates and thermoplastic liner
7.9 Selection of physical properties of materials and allowable design factors
8 Determination of design strain and loadings
8.1 General
8.2 Limit design strains
8.3 Limit design laminate loadings
8.4 Determination of the mechanical values from laminates
8.5 Laminate thickness
9 Design
9.1 Introduction
9.2 Determination of external loads
9.3 Verification by the partial factor method
9.4 Drawings and design calculations
9.5 Design details
10 Design analysis
10.1 Symbols and units
10.2 Vertical vessels or tanks, cylinders under loads (t < 0,01•D)
10.3 Cylindrical shells subject to compressive loadings — critical buckling criteria
10.4 Conical shells
10.5 Dished end
10.6 Design of flat bottoms and skirts for vertical tanks and vessels
10.7 Circumferential seams for cylindrical joints
10.8 Openings, branches and compensating laminate
10.9 Flat Panels or Blind flanges
10.10 Horizontal tanks and vessels
10.11 Large diameter pipes and pipe fittings
11 Bolted flange connections
11.1 General
11.2 Full face flanges design
11.3 Stub flange design with backing ring
11.4 Butt and strap jointed flanges at vessels or tanks
12 Supports for vessels and tanks
12.1 General
12.2 Supports and mountings for tanks and vessels
13 Seismic loading
14 Design calculation for tank and vessel anchorage
14.1 General
14.2 Design for uplift
14.3 Design for anchor bolts
15 Structures and fittings
15.1 General
15.2 Internal structures and fittings
15.3 External structures and fittings
15.4 Lifting devices
16 Local load analysis
17 Quality Control
17.1 General
17.2 Works requirements
17.3 Documentation to be prepared by the manufacturer
17.4 Manufacture
17.5 Inspection and testing after completion of fabrication
17.6 Experimental Design Verification Method for pressure vessel
Annex A (informative) Product testing for serial or batch production process
Annex B (informative) Derivation of laminate properties from laminate properties
Annex C (normative) Pressure and leak testing
Annex D (normative) Methods of tests
Annex E (normative) Approval testing of laminators
Annex F (informative) Design by stress analysis
Annex G (normative) Environmental aspects
Annex ZA (informative) Relationship between this European Standard and the essential requirements of Directive 2014/68/EU aimed to be covered
Bibliography
Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».