ДСТУ EN 1303:2022 Строительная фурнитура. Цилиндры для замков. Требования и методы испытаний (EN 1303:2015, IDT)

ДСТУ EN 1303:2022
(EN 1303:2015, IDT)

Будівельна фурнітура. Циліндри для замків. Вимоги та методи випробувань

 
   
 
 
     
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 Requirements

4.1 General

4.2 Category of use — Key strength

4.3 Durability

4.4 Door mass

4.5 Suitability for use on fire resistant / smoke control doors

4.6 Safety

4.7 Corrosion resistance and operation at extreme temperatures

4.7.1 Corrosion resistance

4.7.2 Operation at extreme temperatures

4.8 Key related security

4.8.1 Minimum number of effective differs

4.8.2 Minimum number of movable detainers

4.8.3 Maximum number of identical steps

4.8.4 Direct coding on key

4.8.5 Operation of security mechanism (inter-passing)

4.8.6 Torque resistance of plug/cylinder relevant to key related security

4.9 Attack resistance

4.9.1 General

4.9.2 Resistance to attack by drilling

4.9.3 Resistance to attack by chisel

4.9.4 Resistance to attack by twisting

4.9.5 Resistance to attack by plug / cylinder extraction

4.9.6 Torque resistance of plug/cylinder relevant to attack resistance

5 Test – General and test apparatus

5.1 General

5.2 Test rigs and apparatus

6 Test methods – procedures

6.1 General

6.2 Key strength

6.3 Durability tests — Standard test cycles

6.4 Door mass

6.5 Suitable for use on fire resistance / smoke control doors

6.6 Safety

6.7 Corrosion resistance and test of operation at extreme temperatures

6.7.1 Corrosion resistance

6.7.2 Test of operation at extreme temperatures

6.8 Key related Security

6.8.1 Minimum numbers of effective differs

6.8.2 Minimum number of movable detainer

6.8.3 Maximum number of identical steps

6.8.4 Direct coding on key

6.8.5 Operation of the security mechanism

6.8.6 Torque resistance of plug and/or cylinder

6.9 Attack resistance

6.9.1 Resistance to drilling

6.9.2 Resistance to attack by chisel

6.9.3 Resistance to attack by twisting

6.9.4 Resistance to attack by plug/cylinder extraction

6.9.5 Torque resistance of plug/cylinder relevant to attack resistance

7 Classification

7.1 General

7.2 Category of use (1st digit)

7.3 Durability (2nd digit)

7.4 Door mass (3rd digit)

7.5 Suitable for use on fire resistant / smoke control doors (4th digit)

7.6 Safety (5th digit)

7.7 Corrosion resistance and temperature (6th digit)

7.8 Key related security (7th digit)

7.9 Attack resistance (8th digit)

8 Marking

Annex A (normative) Cylinders suitable for use on fire resistant / smoke control doors

Annex B (informative) Tables of test sequence

Annex C (informative) Product information

Annex D (informative) Manufacturer’s declaration of compliance

Annex E (informative) Comparison table between EN 1303:2005 and EN 1303:2015

Bibliography