ДСТУ ISO 230-1:2019 Метод испытания станков. Часть 1. Геометрическая точность станков в условиях работы без нагрузки и в квазистатических условиях (ISO 230-1:2012, IDT)

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)

Наказ від 04.11.2019 № 342

ISO 230-1:2012

Test code for machine tools —
Part 1: Geometric accuracy of machines operating
under no-load or quasi-static conditions

прийнято як національний стандарт
методом підтвердження за позначенням

ДСТУ ISO 230-1:2019
(ISO 230-1:2012, IDT)

Метод випробування верстатів.
Частина 1. Геометрична точність верстатів в умовах роботи
без навантаження та у квазістатичних умовах

З наданням чинності від 2019-12-01

 
 
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)  

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

3.1 General

3.2 Terms for machine coordinate system and motion nomenclature

3.3 Terms for static compliance and hysteresis

3.4 Terms for linear axes

3.5 Terms for axes of rotation

3.6 Terms for parallelism error and squareness error of axes of motion

3.7 Terms for other relationships between axis average lines

3.8 Terms for multi-axes motion or kinematic tests

3.9 Terms for geometric accuracy of machine functional surfaces, machine tool components and test pieces

4 Tolerances

4.1 General

4.2 Tolerances applicable to machine tool functional surfaces, machine tool components and test pieces

4.3 Additional limiting conditions associated with tolerances

5 Uncertainty of measurements, test methods and measuring instruments

6 Preliminary operations

6.1 Installation of the machine before tests

6.2 Conditions before machine tests

6.3 Test setup and instrumentation

7 Machine static compliance and hysteresis tests

7.1 General

7.2 Tests for machine static compliance and hysteresis by applying force externally

7.3 Tests for machine static compliance and hysteresis by applying force internally

7.4 Tests for machines with rotary axes

8 Geometric accuracy tests of axes of linear motion

8.1 General

8.2 Straightness error motion tests

8.3 Linear positioning error motion tests

8.4 Angular error motions tests

9 Geometric accuracy tests of axes of rotation

9.1 Reference to ISO 230-7

9.2 Angular positioning error motion

10 Alignment of axes of motion — Parallelism, squareness, coaxiality and intersection

10.1 Parallelism of axes of motion

10.2 Coaxiality error of axis average lines

10.3 Squareness error of axes of motion

10.4 Intersection of axis average lines

11 Multi-axes motion (kinematic) tests

11.1 General

11.2 Linear trajectories

11.3 Circular trajectories

11.4 Conical (shape) motion

11.5 Spherical interpolation test using spherical artefacts and linear displacement sensors

11.6 Flatness error of a surface generated by two axes of linear motion

11.7 Special tests

12 Geometric accuracy tests of machine functional surfaces — Straightness, flatness, perpendicularity and parallelism

12.1 Straightness error of machine functional surfaces

12.2 Flatness of machine tables

12.3 Position and orientation of functional surfaces

12.4 Squareness error and perpendicularity error between lines and planes

12.5 Run-out of rotational components

Annex A (informative) Machine tool coordinate system and position and orientation errors

Annex B (informative) Test piece measurement

Annex C (informative) Cross-reference

Bibliography

Index Alphabetical index of terms and definitions