ДСТУ CISPR 16-1-1:2019 Технические требования к аппаратуре для измерения радиобурь и невосприимчивости и методы измерения. Часть 1-1. Аппаратура для измерения радиобурь и невосприимчивости. Измерительная аппа...

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(   
(ДП «УкрНДНЦ»))

Наказ від 04.12.2019 № 400

CISPR 16-1-1:2015

Specification for radio disturbance and immunity
measuring apparatus and methods —
Part 1-1: Radio disturbance and immunity measuring apparatus —
Measuring apparatus

прийнято як національний стандарт
методом «підтвердження» за позначенням
 

ДСТУ CISPR 16-1-1:2019
(CISPR 16-1-1:2015, IDT)

Технічні вимоги до апаратури для вимірювання радіозбурень
та несприйнятливості та методи вимірювання.
Частина 1-1. Апаратура для вимірювання радіозбурень
та несприйнятливості. Вимірювальна апаратура

З наданням чинності від 2020–01–01

CONTENTS

FOREWORD

INTRODUCTION

1 Scope

2 Normative references

3 Terms and definitions

4 Quasi-peak measuring receivers for the frequency range 9 kHz to 1 000 MHz

4.1 General

4.2 Input impedance

4.3 Sine-wave voltage accuracy

4.4 Response to pulses

4.5 Selectivity

4.6 Limitation of intermodulation effects

4.7 Limitation of receiver noise and internally generated spurious signals

4.8 Screening effectiveness

4.9 Facilities for connection to a discontinuous disturbance analyzer

5 Measuring receivers with peak detector for the frequency range 9 kHz to 18 GHz

5.1 General

5.2 Input impedance

5.3 Fundamental characteristics

5.4 Sine-wave voltage accuracy

5.5 Response to pulses

5.6 Selectivity

5.7 Intermodulation effects, receiver noise, and screening

6 Measuring receivers with average detector for the frequency range 9 kHz to 18 GHz

6.1 General

6.2 Input impedance

6.3 Fundamental characteristics

6.4 Sine-wave voltage accuracy

6.5 Response to pulses

6.6 Selectivity

6.7 Intermodulation effects, receiver noise, and screening

7 Measuring receivers with rms-average detector for the frequency range 9 kHz to 18 GHz

7.1 General

7.2 Input impedance

7.3 Fundamental characteristics

7.4 Sine-wave voltage accuracy

7.5 Response to pulses

7.6 Selectivity

7.7 Intermodulation effects, receiver noise, and screening

8 Measuring receivers for the frequency range 1 GHz to 18 GHz with amplitude probability distribution (APD) measuring function

9 Disturbance analyzers

9.1 General

9.2 Fundamental characteristics

9.3 Test method for the validation of the performance check for the click analyzer

Annex A (normative) Determination of response to repeated pulses of quasi-peak and rms-average measuring receivers (See 3.6, 4.4.2, 7.3.2 and 7.5.1)

Annex В (normative) Determination of pulse generator spectrum (See 4.4, 5.5, 6.5, 7.5)

Annex C (normative) Accurate measurements of the output of nanosecond pulse generators (See 4.4, 5.5, 6.5, 7.5)

Annex D (normative) Influence of the quasi-peak measuring receiver characteristics on its pulse response (See 4.4.2)

Annex E (normative) Response of average and peak measuring receivers (See 6.3.1)

Annex F (normative) Performance check of the exceptions from the definitions of a click according to 4.2.3 of CISPR 14-1:2005

Annex G (informative) Rationale for the specifications of the APD measuring function

Annex H (informative) Characteristics of a quasi-peak measuring receiver

Annex I (informative) Example of EMI receiver and swept spectrum analyzer architecture

Annex J (normative) Requirements when using an external preamplifier with a measuring receiver

Annex К (normative) Calibration requirements for measuring receivers

Bibliography