ДСТУ HD 60269-2:2014 Низковольтные предохранители. Часть 2. Дополнительные требования к предохранителям, которые используются квалифицированными лицами (предохранители в основном промышленные). Примеры станда...
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
Державне підприємство
«Український науково-дослідний і навчальний центр
проблем стандартизації, сертифікації та якості»
(ДП «УкрНДНЦ»)
Наказ від 29.12.2014 № 1480
Наказ від 28.12.2019 № 523
HD 60269-2:2013
Low-voltage fuses —
Part 2: Supplementary requirements
for fuses
for use by authorized persons
(fuses mainly for industrial application) —
Examples of standardized systems of fuses A to K
прийнято як національний стандарт
методом підтвердження за позначенням
ДСТУ HD 60269-2:2014
Низьковольтні запобіжники.
Частина 2. Додаткові вимоги до запобіжників,
що застосовуються кваліфікованими особами
(запобіжники переважно промислового застосування).
Приклади стандартизованих систем запобіжників від А до К
(HD 60269-2:2013, IDT)
З наданням чинності від 2016-01-01
Поновлено чинність від 2020-01-01
до
національного органу стандартизації
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)
CONTENTS
INTRODUCTION
1 General scope
1.1 Scope
1.2 Normative references
Fuse system E - Fuses with fuse-links for bolted connections (BS bolted fuse system)
1 General
1.1 Scope
2 Terms and definitions
3 Conditions for operation in service
4 Classification
5 Characteristics of fuses
5.5 Rated power dissipation of a fuse-link and rated acceptable power dissipation of a fuse-holder
5.6 Limits of time-current characteristics
6 Markings
6.1 Markings of fuse-holders
6.2 Markings of fuse-links
7 Standard conditions for construction
7.1 Mechanical design
7.2 Insulating properties and suitability for insulation
7.9 Protection against electric shock
8 Tests 8.3 Verification of temperature rise and
power dissipation 8.4 Verification of operation
8.5 Verification of breaking capacity
8.9 Verification of resistance to heat
8.10 Verification of non-deterioration of
contacts 8.11 Mechanical and miscellaneous
tests FIGURES
Fuse system G - Fuses with
fuse-links with offset blade contacts (BS clip-in fuse system)
1 General 1.1 Scope 2 Terms and definitions
3 Conditions for operation in
service 4 Classification 5 Characteristics of fuses
5.2 Rated voltage 5.5 Rated power dissipation of a
fuse-link and rated acceptable power dissipation of a
fuse-holder 6 Markings 6.1 Markings of fuse-holders
6.2 Markings of fuse-links
7 Standard conditions for
construction 7.1 Mechanical design 7.2 Insulating properties and
suitability for insulation 7.7 I2t characteristics 7.9 Protection against electric shock
8 Tests 8.9 Verification of resistance to heat
8.10 Verification of non-deterioration of
contacts 8.11 Mechanical and miscellaneous
tests FIGURES Fuse system I - gU fuse-links with
wedge tightening contacts 1 General 1.1 Scope 2 Terms and definitions
3 Conditions for operation in
service 3.9 Discrimination of fuse-links
4 Classification
5 Characteristics of fuses
5.2 Rated voltage 5.5 Rated power dissipation of a
fuse-link 5.8 Cut-off current and I2t
characteristics 6 Markings 6.1 Markings of fuse-holders
6.2 Markings of fuse-links
7 Standard conditions for
construction 7.1 Mechanical design 7.2 Insulating properties and
suitability for insulation 7.5 Breaking capacity 7.7 I2t characteristics 7.8 Overcurrent discrimination of the
fuse-links 8 Tests
8.9 Verification of resistance
to heat 8.11 Mechanical and miscellaneous tests
FIGURES Bibliography
Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».