ДСТУ EN ISO 19085-15:2022 Верстати деревообробні. Безпека. Частина 15. Преси (EN ISO 19085-15:2021, IDT; ISO 19085-15:2021, IDT)



ДСТУ EN ISO 19085-15:2022
(EN ISO 19085-15:2021, IDT; ISO 19085-15:2021, IDT)

Верстати деревообробні. Безпека. Частина 15. Преси

 
   
 
 
     
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)

Contents

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 List of significant hazards

5 Safety requirements and measures for controls

5.1 Safety and reliability of control systems

5.2 Control devices

5.3 Start

5.4 Safe stops

5.4.1 General

5.4.2 Normal stop

5.4.3 Operational stop

5.4.4 Emergency stop

5.5 Braking function of tool spindles

5.6 Mode selection

5.7 Spindle speed changing

5.7.1 Spindle speed changing by changing belts on the pulleys

5.7.2 Spindle speed changing by incremental speed change motor

5.7.3 Infinitely variable speed by frequency inverter

5.8 Failure of any power supply

5.9 Manual reset control

5.10 Enabling control

5.11 Machine moving parts speed monitoring

5.12 Time delay

6 Safety requirements and measures for protection against mechanical hazards

6.1 Stability

6.1.1 General

6.1.2 Displaceable machines

6.2 Risk of break-up during operation

6.3 Tool holder and tool design

6.3.1 General

6.3.2 Spindle locking

6.3.3 Circular saw blade fixing devices

6.3.4 Flange dimensions for circular saw blades

6.4 Braking

6.4.1 Braking of tool spindles

6.4.2 Maximum run-down time

6.4.3 Brake release

6.5 Safeguards

6.5.1 Fixed guards

6.5.2 Interlocking moveable guards

6.5.2.1 General

6.5.2.2 Moveable guards with interlocking without guard locking

6.5.2.3 Moveable guards with interlocking and guard locking

6.5.3 Hold-to-run control

6.5.4 Two hand control

6.5.5 Electro-sensitive protective equipment (ESPE)

6.5.6 Pressure sensitive protective equipment (PSPE)

6.6 Prevention of access to moving parts

6.6.1 General

6.6.2 Guarding of tools

6.6.3 Guarding of drives

6.6.4 Guarding of shearing and/or crushing zones

6.6.4.1 Safeguarding of cold and hot presses with manual loading and unloading

6.6.4.2 Safeguarding of bending presses with manual loading and unloading

6.6.4.3 Safeguarding of edge/face gluing presses with manual loading and unloading

6.6.4.4 Safeguarding of membrane presses with manual loading and unloading

6.6.4.5 Safeguarding of embossing presses with manual loading and unloading

6.6.4.6 Safeguarding of machines with automatic work-piece loading/unloading systems type 1, type 2 and type 3

6.6.4.7 Safeguarding of machines with automatic work-piece loading/unloading system type 4

6.6.4.8 Safeguarding of machines with automatic work-piece loading/unloading system type 5

6.6.4.9 Safeguarding of machines with automatic work-piece loading/unloading system type 6

6.7 Impact hazard

6.8 Clamping devices

6.9 Measures against ejection

6.9.1 General

6.9.2 Guards materials and characteristics

6.9.2.1 Choice of class of guards

6.9.2.2 Guards of class A

6.9.2.3 Guards of class B

6.10 Work-piece support and guides

7 Safety requirements and measures for protection against other hazards

7.1 Fire

7.2 Noise

7.2.1 Noise reduction at the design stage

7.2.2 Noise emission measurement and declaration

7.3 Emission of chips and dust

7.4 Electricity

7.4.1 General

7.4.2 Displaceable machines

7.5 Ergonomics and handling

7.6 Lighting

7.7 Pneumatics

7.8 Hydraulics

7.9 Electromagnetic compatibility

7.10 Laser

7.11 Static electricity

7.12 Errors of fitting

7.13 Isolation

7.14 Maintenance

7.15 Extreme temperatures

8 Information for use

8.1 Warning devices

8.2 Marking

8.2.1 General

8.2.2 Additional markings

8.3 Instruction handbook

8.3.1 General

8.3.2 Additional information

Annex A (informative) Performance level required

Annex B (normative) Tests for braking function

Annex C (normative) Stability test for displaceable machines

Annex D (normative) Impact test for guards

Annex E (normative) Noise test code

Bibliography