ДСТУ IEC 60092-350:2016 Установки електричні на суднах. Частина 350. Загальна конструкція та методи випробування силових, контрольних та інструментальних кабелів для суден і морських застосувань (IEC 60092-35...

ДСТУ ІЕС 60092-350:2016
(ІЕС 60092-350:2014, IDT)

Установки електричні на суднах. Частина 350. Загальна
конструкція та методи випробування силових, контрольних та
інструментальних кабелів для суден і морських застосувань

 
   
 
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)

Contents

Foreword

1 Scope

2 Normative references

3 Terms and definitions

4 Construction requirements

4.1 General requirements

4.2 Conductors

4.3 Insulation system

4.4 Screens

4.5 Cabling

4.6 Inner coverings, fillers and binders

4.7 Inner sheath

4.8 Metal braid armour

4.9 Outer sheath

5 Test methods

5.1 Test conditions

5.2 Routine tests

6 Sample tests

6.1 General

6.2 Frequency of sample tests

6.3 Repetition of tests

6.4 Conductor examination

6.5 Measurement of thickness of insulation

6.6 Measurements of thickness of non-metallic sheaths

6.7 Measurement of external diameter

6.8 Hot-set test for insulations and sheaths

6.9 Insulation resistance test (volume resistivity determination)

7 Type tests, electrical

7.1 General

7.2 Insulation resistance measurement

7.3 Increase in a.c. capacitance after immersion in water

7.4 High-voltage test for 4 h up to 1,8/3 kV

7.5 Mutual capacitance (control and instrumentation cables only)

7.6 Inductance to resistance ratio (control and instrumentation cables only)

7.7 High voltage sequence test (cables having a voltage rating higher than 3,6/6 (7,2) kV)

8 Type tests, non-electrical

8.1 General

8.2 Measurement of thickness of insulation

8.3 Measurement of thickness of non-metallic sheaths (excluding inner coverings)

8.4 Tests for determining the mechanical properties of insulation before and after ageing

8.5 Tests for determining the mechanical properties of sheaths before and after ageing

8.6 Additional ageing test on pieces of completed cables (compatibility test)

8.7 Loss of mass test on PVC ST2 sheath

8.8 Test for the behaviour of PVC ST2 and halogen-free SHF 1 sheaths at high temperature (hot pressure test)

8.9 Test for the behaviour of PVC sheath ST2 and halogen-free SHF 1 and SHF 2 sheaths at low temperature

8.10 Special test for low temperature behaviour (when required)

8.11 Test of the metal coating of copper wires

8.12 Galvanizing test

8.13 Test for resistance of PVC ST2 and halogen-free SHF1 sheaths to cracking (heat shock test)

8.14 Ozone resistance test for insulation and for sheaths

8.15 Hot oil immersion test and enhanced hot oil immersion test for sheaths

8.16 Mud drilling fluid test (when required)

8.17 Fire tests

8.18 Determination of hardness for HEPR

8.19 Determination of elastic modulus for HEPR

8.20 Durability of print

Annex A (normative) Fictitious calculation method for determination of dimensions of protective coverings

Annex В (informative) Recommended minimum spark test voltage levels (according to IEC 62230)

Annex C (normative) Rounding of numbers

Annex D (normative) Calculation of the lower and upper limits for the outer dimensions of cables with circular copper conductors

Annex E (normative) Cold bend test and impact test for low temperature behaviour

Bibliography