ДСТУ EN 61029-1:2014 Інструменти пересувні з електроприводом. Безпека. Частина 1. Загальні вимоги (EN 61029-1:2009, EN 61029-1:2009/A11:2010, EN 61029-1:2009/AC:2009, IDT)
ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ
МІНІСТЕРСТВО ЕКОНОМІЧНОГО РОЗВИТКУ І ТОРГІВЛІ УКРАЇНИ
Наказ від 29.12.2014 № 1479
EN 61029-1:2009, EN 61029-1:2009/A11:2010, EN 61029-1:2009/AC:2009
Safety of transportable motor-operated electric tools. General requirements
прийнято як національний стандарт
методом «підтвердження» за позначенням
ДСТУ EN 61029-1:2014
(EN 61029-1:2009, EN 61029-1:2009/A11:2010, EN 61029-1:2009/AC:2009, IDT)
Інструменти пересувні з електроприводом. Безпека. Частина 1. Загальні вимоги
З наданням чинності від 2016-01-01
Contents
Foreword
Introduction
1 Scope
2 Definitions
2.1 Rated voltage
2.2 Rated voltage range
2.3 Working voltage
2.4 Rated input
2.5 Rated current
2.6 Rated frequency
2.7 Rated frequency range
2.8 Rated no-load speed
2.9 Detachable flexible cord
2.10 Power supply cord
2.11 Basic insulation
2.12 Supplementary insulation
2.13 Double insulation
2.14 Reinforced insulation
2.15 Class I tool
2.16 Class II tool
2.17 Class III tool
2.18 Extra-low voltage
2.19 Safety extra-low voltage (SELV)
2.20 Safety isolating transformer
2.21 Normal load
2.22 Rated operating time
2.23 Continuous operation
2.24 Short-time operation
2.25 Intermittent operation
2.26 Non-detachable part
2.27 Detachable part
2.28 Thermal cut-out
2.29 Non-self-resetting thermal cut-out
2.30 Creepage distance
2.31 Clearance
2.32 All-pole disconnection
2.33 Accessible part or accessible surface
2.34 Power circuit
2.35 Control circuit
2.36 Control device
2.37 PRCD
3 General requirement
4 General notes on tests
5 Rating
6 Classification
7 Marking and information for use
8 Protection against electric shock
9 Starting
10 Input and current
11 Heating
12 Leakage current
13 Environmental requirements
13.1 Dust measurement
13.2 Noise
13.3 Vibration
14 Protection against ingress of foreign bodies and moisture resistance
15 Insulation resistance and electric strength
16 Endurance
17 Abnormal operation
18 Stability and mechanical hazards
19 Mechanical strength
20 Construction
21 Internal wiring
22 Components
23 Supply connection and external flexible cables and cords
24 Terminals for external conductors
25 Provision for earthing
26 Screws and connection
27 Creepage distances, clearances and distances through insulation
28 Resistance to heat, fire and tracking
29 Resistance to rusting
30 Radiation
Annex A (normative) Normative references
Annex В (normative) Thermal cut-outs and overload releases
Annex C (normative) Electronic circuits
Annex D (normative) Measurement of creepage distances and clearances
Annex IA (informative) Circuit for measuring leakage currents
Annex ZA (informative) Rules for routine tests
Annex ZB (normative) Special national conditions
Annex ZC (informative) Possible sources of errors during vibration measurements
Annex ZD (informative) Dust measurement
Повна версія документа доступна в тарифі «ВСЕ ВРАХОВАНО».