ДСТУ EN 50604-1:2022 Вторичные литиевые батареи для легких электромобилей (электрических транспортных средств). Часть 1. Общие требования по безопасности и методы испытания (EN 50604-1:2016, IDT)



ДСТУ EN 50604-1:2022
(EN 50604-1:2016, IDT)

Вторинні літієві батареї для легких електромобілів (електричних транспортних засобів). Частина 1. Загальні вимоги щодо безпеки та методи випробування

 
   
 
 
     
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)

Contents

European foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 Symbols and abbreviated terms

5 General requirements

5.1 General

5.2 Test sequence plan

5.3 Preparation of the OUT fortesting

5.4 Pre-conditioning cycles

5.5 General safety requirements

6 Mechanical tests

7 Climatic tests

7.1 Dewing (temperature change)

7.2 Thermal shock cycling

8 Simulated vehicle accidents

8.1 Inertial load at vehicle crash

8.2 Contact force at vehicle crash

8.3 Water immersion

8.4 Exposure to fire

9 Electrical tests

10 System functionality tests

Annex AA (informative) Battery Systems and related parts

AA.1 General

AA.2 Battery pack

AA.3 Battery system

AA.3.1 Battery system with integrated BCU/BMS

AA.3.2 Battery system with external BCU/BMS

Annex BB (normative) General marking requirements

BB.1 Marking and instructions

BB.1.1 Removable (RESS) battery systems (packs) marking

BB.1.2 Graphical symbols

BB.2 Instructions

BB.3 Instructions for built-in battery system

BB.4 Language

BB.5 Label test

BB.6 Markings

Annex CC (normative) Test stamp for crush test

Annex DD (normative) Test probe

Annex EE (informative) Packaging and transportation for not tested battery samples

EE.1 Information regarding packaging and transportation

EE.1.1 Sample classification

EE.1.2 Labelling

EE.1.3 Packaging

EE.1.4 Transport or shipper's declaration

EE.1.5 List of content of package

EE.2 Documents

EE.2.1 Form with data regarding the properties of substances of cells

EE.2.2 Handling instructions and guidelines for cells and battery packs

EE .2.3 Operation manual of battery packs, chargers (VCUs), PC В or BMS

EE.2.4 Certificates for components and subsystems

EE.2.5 Quality examination report of samples

EE.2.6 Overview about provided samples and their respective cycle history

EE.3 Additional information

EE.3.1 Instructions on bypassing protective devices

EE.3.2 Other information

Annex FF (informative) Transport regulations

FF.1 Regulatory information

FF.2 UN-Numbers

FF.3 Transport information

FF.4 UN Recommendations on the Transport of Dangerous Goods

FF.5 UN Recommendations on the Transport of Dangerous Goods - Manual of Test and Criteria

FF.6 Overview about UN-T Tests T.1 - T.8 lithium, lithium ion and lithium polymer cells and batteries

FF.6.1 Test T.1: Altitude simulation

FF.6.2 Test T.2: Thermal test

FF.6.3 Test T.3: Vibration

FF.6.4 Test T.4: Shock

FF.6.5 Test T.5: External Short Circuit

FF.6.6 Test T.6: Impact

FF.6.7 Test T.7: Overcharge

FF.6.8 Test T.8: Forced Discharge

Annex GG (normative) Test sequences and number of samples

Bibliography

Figure AA.1 — Typical configuration of a battery pack

Figure AA.2 — Typical configuration of a battery system with integrated BCU/BMS

Figure AA.3 — Typical configuration of a battery system with external BCU

Figure DD.1 — Test probe “test finger”

Table 1 — Battery system requirements

Table BB.1 — Graphical symbols

Table FF.1 — Comparison of test items

Table GG.1 — Number of samples required