ДСТУ EN ISO 13705:2022 Нефтяная, нефтехимическая и газовая промышленность. Нагреватели с огнем для общего обслуживания нефтеперерабатывающих заводов (EN ISO 13705:2012, IDT; ISO 13705:2012, IDT)
ДСТУ EN ISO 13705:2022
(EN ISO 13705:2012, IDT; ISO 13705:2012, IDT)
Нафтова, нафтохімічна та газова промисловість. Нагрівачі з вогнем
для загального обслуговування нафтопереробних заводів
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)
Contents
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, abbreviated terms and symbols
3.1 Terms and definitions
3.2 Abbreviated terms and symbols
4 General
4.1 Pressure design code
4.2 Regulations
4.3 Heater nomenclature
5 Proposals
5.1 Purchaser's responsibilities
5.2 Vendor's responsibilities
5.3 Documentation
5.4 Final reports
6 Design considerations
6.1 Process design
6.2 Combustion design
6.3 Mechanical design
7 Tubes
7.1 General
7.2 Extended surface
7.3 Materials
8 Headers
8.1 General
8.2 Plug headers
8.3 Return bends
8.4 Materials
9 Piping, terminals and manifolds
9.1 General
9.2 Allowable movement and loads
9.3 Materials
10 Tube supports
10.1 General
10.2 Loads and allowable stress
10.3 Materials
11 Refractories and insulation
11.1 General
11.2 Brick and tile construction
11.3 Castable construction
11.4 Ceramic-fibre construction
11.5 Multi-component lining construction
11.6 Materials
12 Structures and appurtenances
12.1 General
12.2 Structures
12.3 Header boxes, doors and ports
12.4 Ladders, platforms and stairways
12.5 Materials
13 Stacks, ducts and breeching
13.1 General
13.2 Design considerations
13.3 Design methods
13.4 Static design
13.5 Wind-induced vibration design
13.6 Materials
14 Burners and auxiliary equipment
14.1 Burners
14.2 Sootblowers
14.3 Fans and drivers
14.4 Dampers and damper controls for stacks and ducts
15 Instrument and auxiliary connections
15.1 Flue gas and air
15.2 Process fluid temperature
15.3 Auxiliary connections
15.4 Tube-skin thermocouples
15.5 Access to connections
16 Shop fabrication and field erection
16.1 General
16.2 Structural-steel fabrication
16.3 Coil fabrication
16.4 Painting and galvanizing
16.5 Refractories and insulation
16.6 Preparation for shipment
16.7 Field erection
17 Inspection, examination and testing
17.1 General
17.2 Weld examination
17.3 Castings examination
17.4 Examination of other components
17.5 Testing
Annex A (informative): Equipment data sheets
Annex B (informative): Purchaser's checklist
Annex C (informative): Proposed shop-assembly conditions
Annex D (normative): Stress curves for use in the design of tube-support elements
Annex E (normative): Centrifugal fans for fired-heater systems
Annex F (normative): Air preheat systems for fired process heaters
Annex G (informative): Measurement of efficiency of fired process heaters
Annex H (informative): Stack design
Annex I (informative): Measurement of noise from fired-process heaters
Bibliography
Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».