ДСТУ EN 50131-3:2014 Системы тревожной сигнализации. Системы охранной сигнализации. Часть 3. Приборы приемно-контрольные (EN 50131-3:2009, IDT)

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

МІНІСТЕРСТВО ЕКОНОМІЧНОГО РОЗВИТКУ І ТОРГІВЛІ УКРАЇНИ

Наказ від 30.12.2014 № 1494

EN 50131-3:2009

Alarm systems -
Intrusion and hold-up systems -
Part 3: Control and indicating equipment

прийнято як національний стандарт
методом «підтвердження» за позначенням
 

ДСТУ EN 50131-3:2014
(EN 50131-3:2009, IDT)

Системи тривожної сигналізації. Системи охоронної сигналізації.
Частина 3. Прилади приймально-контрольні

З наданням чинності від 2016-01-01

Contents

Introduction

1 Scope

2 Normative references

3 Definitions and abbreviations

3.1 Definitions

3.2 Abbreviations

4 Equipment attributes

4.1 General

4.2 Functionality

5 CIE construction

6 Security grade

7 Environmental performance

7.1 Requirements

7.2 Environmental and EMC tests

8 Functional requirements

8.1 Inputs

8.2 Outputs

8.3 Operation

8.4 Processing

8.5 Indication

8.6 Notification outputs

8.7 Tamper security (detection/protection)

8.8 Interconnections

8.9 Timing

8.10 Event recording

8.11 Power supply

9 Product documentation

9.1 Installation and maintenance

9.2 Operating instructions

10 Marking and labelling

11 Tests

11.1 Test conditions

11.2 Test procedures

11.3 Reduced functional test

11.4 Functional tests

11.5 Access level

11.6 Authorization requirements

11.7 Operational tests

11.8 Tamper security tests

11.9 Substitution tests

11.10 Testing of I&HAS timing performance

11.11 Testing for interconnections

11.12 Event log

11.13 Marking and documentation

11.14 Environmental and EMC tests

Annex A (informative) Interconnection types

Annex B (informative) Summary of timing requirements

Annex C (normative) Use of non-I&HAS interface

Annex D (informative) Summary of function cross references

Figures

Figure A.1 – Specific wired interconnections

Figure A.2 – Non-specific wired interconnections

Figure A.3 – Wire-free interconnections

Tables

Table 1 – Recognition of additional fault conditions

Table 2 – Recognition of biometric keys

Table 3 – Time intervals for methods of authorization used in combination

Table 4 – Detection of repeated invalid authorization attempts

Table 5 – Monitoring of processing

Table 6 – Indications supplementary to those of EN 50131-1

Table 7 – Tamper protection

Table 8 – Tamper detection

Table 9 – Tool dimension for tamper detection

Table 10 – Removal from mounting

Table 11 – Additional events to be included in event log

Table 12 – Reduced functional test

Table 13 – Tests of the processing of intruder signals or messages

Table 14 – Tests of the processing of hold-up signals or messages

Table 15 – Tests of the processing of tamper signal or messages

Table 16 – Test of processing of fault signals or messages

Table 17 – Test of processing of masking signals or messages

Table 18 – Test of processing of reduction of range signals or messages

Table 19 – Test of CIE processing in the presence of non-I&HAS inputs

Table 20 – Test of the access to the functions and controls

Table 21 – Test for disabling user input device by invalid keys

Table 22 – Test for generation of tamper by invalid keys

Table 23 – Test of setting procedure

Table 24 – Test of prevention of setting and overriding of prevention of setting procedure

Table 25 – Test for unsetting procedure

Table 26 – Test of setting and/or unsetting automatically at pre-determined times

Table 27 – Inhibit and isolate functions

Table 28 – Verification of test functions

Table 29 – Test of CIE process monitoring

Table 30 – Test of availability of indications

Table 31 – Test of event log

Table 32 – Environmental and EMC tests

Table B.1 – Timing table

Table C.1 – Conditions for use of non-I&HAS interface for control and indicating purposes

Table D.1 – Cross references

Bibliography