ДСТУ EN 50132-5-3:2014 Системы тревожной сигнализации. Системы видеонаблюдения охранного назначения. Часть 5-3. Аналоговая и цифровая передача видео (EN 50132-5-3:2012, IDT)

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Наказом Міністерства економічного розвитку і торгівлі України
від 30.12.2014 № 1494

EN 50132-5-3:2012

en: Alarm systems - CCTV surveillance systems for use in security applications -
Part 5- 3: Video transmission - Analogue and digital video transmission

прийнято як національний стандарт
методом підтвердження за позначенням

ДСТУ EN 50132-5-3:2014

Системи тривожної сигналізації.
Системи відеоспостереження охоронного призначення.
Частина 5-3. Аналогове та цифрове передавання відео

(ЕN 50132-5-3:2012, IDТ)

З наданням чинності від 2016-01-01

Contents

Foreword

Introduction

Scope

Normative references

Terms, definitions and abbreviations

3.1 Terms and definitions

3.2 Abbreviations

4 Analogue video signal transmission requirements

4.1 General

4.2 Video input and output

4.3 Insertion gain

4.4 Bandwidth and frequency response

4.5 Signal to noise ratio

4.6 Interference

4.7 Luminance non-linearity

4.8 Chrominance to luminance gain inequality

4.9 Chrominance to luminance delay inequality

4.10 Differential gain

4.11 Differential phase

4.12 Environmental conditions

4.13 Electromagnetic radiation

4.14 Immunity to electromagnetic interference

4.15 Electrical safety

5 Analogue video signal transmission test conditions 

5.1 Introduction

5.2 Test equipment

5.3 Laboratory conditions

6 Analogue video signal transmission performance tests

6.1 Input and output signal levels

6.2 Insertion gain

6.3 Input and output impedance

6.4 DC voltage at the output

6.5 Short time waveform distortion

6.6 Line time waveform distortion

6.7 Field time waveform distortion

6.8 Damped low frequency distortion

6.9 Chrominance to luminance gain and delay inequality

6.10 Signal to noise ratio

6.11 Interference

6.12 Luminance non-linearity

6.13 Differential gain

6.14 Differential phase

7 Video signal transmission equipment environmental testing

7.1 Introduction

7.2 Selection of tests and severity

7.3 Dry heat (operational)

7.4 Dry heat (endurance)

7.5 Cold (operational)

7.6 Damp heat, steady state (operational)

7.7 Damp heat, steady state (endurance)

7.8 Damp heat, cyclic (operational)

7.9 Damp heat, cyclic (endurance)

7.10 Water ingress (endurance)

7.11 Sulphur dioxide (S0₂) (endurance)

7.12 Salt mist, cyclic (endurance)

7.13 Shock (operational)

7.14 Vibration, sinusoidal (operational)

7.15 Vibration, sinusoidal (endurance)

8 Analogue video signal transmission equipment documentation

8.1 Documentation

8.2 Marking and labelling

9 High resolution video interface standards & transmission requirements

9.1 General

9.2 Introduction

9.3 General requirements

9.4 VESA DMT interface standards and guidelines reference

9.5 High definition interface: Uncompressed High Speed Digital Video DVI / HDMI

Annex A (normative) Analogue video signal test patterns

A.1 Signal A

A.2 Signal В

A.3 Signal С

4 Signal D

A 5 Signal F

Annex В (normative)

B.1 Chrominance to luminance amplitude and delay errors

B.2 The Rosman nomogram

B.3 Damped low frequency distortion

B.4 2T waveform mask

Bibliography

Figures

Figure 1

Figure A.1 - Signal A: half frame white and black bar signal

Figure A.2 - Signal B: pulse and bar signal

Figure A.3 - Signal C: frequency burst

Figure A.4 - Signal D1: grey scale signal

Figure A.5 - Signal D2: grey scale signal

Figure A.6 - Signal F: 20T pulse

Figure B.1

Figure B.2

Figure B.3

Figure B.4

Tables

Table 1 - Summary of Display Monitor Timings - Standards and guidelines

Table 2

Table 3