ДСТУ EN 61000-3-2:2015 Электромагнитная совместимость. Часть 3-2. Нормы. Нормы на эмиссию гармоник тока (для силы входного тока оборудования не более 16 А на фазу) (EN 61000-3-2:2014, IDT)

ПІДТВЕРДЖУВАЛЬНЕ ПОВІДОМЛЕННЯ

Український науково-дослідний і навчальний центр проблем стандартизації,
сертифікації та якості (   
(ДП «УкрНДНЦ»))

Наказ від 28.09.2015 №118

EN 61000-3-2:2014

en: Electromagnetic compatibility (EMC) — Part 3-2: Limits — Limits for harmonic
current emissions (equipment input current < 16 A per phase)

прийнято як національний стандарт
методом підтвердження за позначенням

ДСТУ EN 61000-3-2:2015

uk: Електромагнітна сумісність. Частина 3-2. Норми. Норми на емісію
гармонік струму (для сили вхідного струму обладнання не більше ніж 16 А на фазу)
(EN 61000-3-2:2014, IDT)

З наданням чинності від 2016-01-01

CONTENTS

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 General

5 Classification of equipment

6 General requirements

6.1 Control methods

6.2 Harmonic current measurement

6.2.1 Test configuration 

6.2.2 Measurement procedure

6.2.3 General requirements

6.2.4 Test observation period

6.3 Equipment in a rack or case

7 Harmonic current limits

7.1 Limits for Class A equipment

7.2 Limits for Class B equipment

7.3 Limits for Class C equipment

7.4 Limits for Class D equipment

Annex A (normative) Measurement circuit and   supply source

A.1 Test circuit

A.2 Supply source

Annex B (normative) Requirements for measurement equipment 

Annex C (normative) Type test conditions

C.1 General

C.2 Test conditions for television (TV) receivers

C.2.1 General conditions

C.2.2 Conditions for measurement

C.3 Test conditions for audio amplifiers

C.3.1 Conditions

C.3.2 Input signals and loads

C.4 Test conditions for video-cassette recorders

C.5 Test conditions for lighting equipment

C.5.1 General conditions

C.5.2 Lamps 

C.5.3 Luminaires

C.5.4 Ballasts and step-down converters

C.6 Test conditions for independent and built-in incandescent lamp dimmers

C.7 Test conditions for vacuum cleaners

C.8 Test conditions for washing machines

C.9 Test conditions for microwave ovens

C.10 Test conditions for information technology equipment (ITE)

C.10.1 General conditions

C.10.2 Optional conditions for measuring emissions of IT equipment with external power supplies or battery chargers

C.11 Test conditions for induction hobs

C.12 Test conditions for air conditioners

C.13 Test conditions for kitchen machines as defined in IEC 60335-2-14   

C.14 Test conditions for arc welding equipment which is not  professional equipment 

C.15 Test conditions for high pressure cleaners which are not professional equipment 

C.16 Test conditions for refrigerators and freezers

C.16.1 General

C.16.2 Refrigerators and freezers with VSD

C.16.3 Refrigerators and freezers without VSD

Bibliography

Figure 1 - Flowchart for determining conformity  

Figure 2 - Illustration of the relative phase angle and current parameters described in 7.3 b)    

Figure A.1 - Measurement circuit for single-phase equipment 

Figure A.2 - Measurement circuit for three-phase equipment

Table 1 - Limits for Class A equipment

Table 2 - Limits for Class C equipment   

Table 3 - Limits for Class D equipment

Table 4 - Test observation period

Table C.1 - Conventional load for arc welding equipment tests