ДСТУ EN 13477-2:2022 Неразрушающий контроль. Акустическая эмиссия. Характеристика оборудования. Часть 2. Эксплуатационные показатели (EN 13477-2:2021, IDT)

Данный документ доступнен в тарифе «ВСЕ ВКЛЮЧЕНО»

У Вас есть вопросы по документу? Мы рады на них ответить!Перечень бесплатных документовОбнаружили ошибку в документе или на сайте? Пожалуйста, напишите нам об этом!Оставить заявку на документ


ДСТУ EN 13477-2:2022
(EN 13477-2:2021, IDT)

Неруйнівний контроль. Акустична емісія. Характеристика обладнання. Частина 2. Експлуатаційні показники




 
     
Не є офіційним виданням.
Офіційне видання розповсюджує національний орган стандартизації
(ДП «УкрНДНЦ» http://uas.gov.ua)

Contents

European foreword

1 Scope

2 Normative references

3 Terms and definitions

4 Required test equipment and test signals

4.1 List of required equipment

4.2 Test signal waveforms

4.2.1 Continuous sine wave

4.2.2 Triangular-modulated sine wave burst signal

4.2.3 Sin2-modulated sine wave burst signal

4.2.4 Rectangular-modulated sine wave burst signal

4.2.5 Rectangular pulse

4.2.6 Repetitive signals

4.2.7 DC signal

4.2.8 Summary of test signals

4.3 Test block

4.4 Shielding test plate

5 Sensor verification

5.1 General

5.2 Intended purpose

5.3 Preparation of the report form and preliminary examination

5.4 Sensitivity verification

5.4.1 General

5.4.2 Test procedure

5.5 Verification of the electrical shield crosstalk

5.5.1 General

5.5.2 Procedure

5.6 Pre-amplifier verification of sensor-internal pre-amplifier

6 Pre-amplifier verification

6.1 Preparation of the report form and preliminary examination

6.2 Verification of DC consumption

6.2.1 General

6.2.2 Verifying a limit or a deviation

6.2.3 Procedure

6.3 Verification of the pre-amplifier characteristics

6.3.1 General

6.3.2 Gain verification

6.3.3 Bandwidth verification

6.3.4 Electronic noise verification

6.3.5 Dynamic range verification

6.3.6 Common mode rejection verification

6.3.7 Pulsing test

7 Acoustic emission signal processor verification

7.1 General

7.1.1 Overview

7.1.2 Preparation of the report form

7.2 Signal processor noise verification

7.2.1 General

7.2.2 Test procedure

7.3 Verification of RMS measurement and floating threshold functionality

7.3.1 General

7.3.2 Test procedure

7.4 Verification of the fixed detection threshold

7.4.1 General

7.4.2 Procedure for signal stimulation and data acquisition

7.4.3 Procedure for the data verification

7.5 Bandwidth and filter roll-off verification

7.5.1 General

7.5.2 Data needed for verification of bandwidth and roll-off verification

7.5.3 Procedure for signal stimulation and storage

7.5.4 Test procedure for bandwidth verification based on stored AE data

7.6 Burst signal parameter verification

7.6.1 General

7.6.2 Maximum amplitude verification

7.6.3 Duration verification

7.6.4 Rise-time verification

7.6.5 Ring-down count verification

7.6.6 Energy and signal strength verification

8 Verification of the system performance

8.1 External parametric input verification

8.1.1 General

8.1.2 Formulae for parametric input verification

8.1.3 Avoiding the use of a high-accuracy digital voltmeter (HADVM)

8.1.4 Report form preparation

8.1.5 Test procedure for signal stimulation and measurement for parametric input verification

8.1.6 Test procedure for parametric input data verification

8.2 Pulser verification

8.3 System acquisition rate verification

8.4 Delta t (Δt) measurement verification

8.5 Software verification

9 Test report

Annex A (informative) Report form for the sensor performance verification

Annex B (informative) Report form for the pre-amplifier performance verification

Annex C (informative) Report form for the acoustic emission signal processor verification

Annex D (informative) Report form for the external parametric input verification

Annex E (informative) List of designations

Bibliography

Полная версия документа доступна в тарифе «ВСЕ ВКЛЮЧЕНО».

Войти в Личный кабинет Подробнее о тарифах

БУДСТАНДАРТ Online